|
Video input — XTP CP 4i, XTP CP 4i DMA
|
|
Number/signal type
|
4 sets of proprietary twisted pair AV signals
|
|
Connectors
|
4 female RJ-45 per board
|
|
NOTE
|
Input comes from an Extron XTP Series twisted pair transmitter.
|
|
|
Video output — XTP CP 4o
|
|
Number/signal type
|
4 sets of proprietary twisted pair AV signals
|
|
Connectors
|
4 female RJ-45 per board
|
|
NOTE
|
Output connects to an Extron XTP Series twisted pair receiver.
|
|
|
Video — XTP CP 4i VGA
|
|
Gain
|
Unity
|
|
Bandwidth
|
300 MHz (-3 dB), fully loaded
0-10 MHz: no more than +0.1 dB to -0.1 dB
0-130 MHz: no more than +0.8 dB to -0.8 dB
|
|
Crosstalk
|
-88 dB @ 1 MHz, -55 dB @ 10 MHz, -45 dB @ 30 MHz, -37 dB @ 100 MHz
|
|
Switching speed
|
200 ms (max.)
|
|
Video input — XTP CP 4i VGA
|
|
Number/signal type
|
4 analog VGA-QXGA RGBHV, RGBS, RGsB, RsGsBs, HDTV, component video, S-video, composite video
|
|
Connectors
|
4 female 15-pin HD
|
|
Nominal level
|
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
|
|
Minimum/maximum levels
|
Analog: 0.5 V to 2.0 Vp-p with no offset
|
|
Impedance
|
75 ohms
|
|
Return loss
|
<-30 dB @ 5 MHz
|
|
DC offset (max. allowable)
|
1.5 V
|
|
Video processing — XTP CP 4i VGA
|
|
Decoder
|
8 bit digital
|
|
Digital sampling
|
30 bit, 10 bits per color; 162 HMz standard
|
|
Colors
|
1 billion
|
|
|
|
Sync — XTP CP 4i VGA
|
|
Input type
|
RGBHV, RGBS, RGsB, RsGsBs
|
|
Input level
|
0.5 V to 5.0 Vp-p, 4.0 Vp-p normal
|
|
Input impedance
|
510 ohms
|
|
Horizontal frequency
|
15 kHz to 150 kHz
|
|
Vertical frequency
|
30 Hz to 150 Hz
|
|
Max. propagation delay
|
30 ns
|
|
Max. rise/fall time
|
4 ns
|
|
Polarity
|
Positive or negative
|
|
Video — XTP CP 4i DVI Pro, XTP CP 4o DVI Pro
|
|
NOTE
|
*Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output.
|
|
|
Gain
|
Unity
|
|
Resolution range
|
Up to 1080p (HDTV) or 1920x1200 (the highest resolution of the single link DVI standard) @ 60 Hz
|
|
Signal type
|
Single link DVI digital video signals are supported.
|
|
Digital video
|
RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component
video (HDMI), actively buffered (supports all single link DVI and HDMI (if using an optional adapter) standards from 640x480 @ 60 Hz to 1920x1200 @ 60 Hz computer video)
|
|
NOTE
|
These XTP CP DVI Pro boards are compatible with HDMI 1.3.
|
|
|
Digital audio
|
Supports HDMI audio (if using an HDMI to DVI adapter) transmitted through the RGB and Y, Cr, Cb lines, actively buffered.
|
|
Consumer Electronics Control (CEC)
|
Not supported
|
|
EDID and DDC
|
Supports Extended Display Identification Data (EDID) and Display Data
Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered.
|
|
HDCP
|
Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI 1.3 standards
|
|
HPD
|
Supports hot plug detection (HPD) of display as a pass-through signal.
|
|
Maximum data rate
|
6.75 Gbps (2.25 Gbps per color)
|
|
Maximum pixel clock
|
165 MHz
|
|
Standards
|
DVI 1.0, HDMI 1.3, HDCP 1.1
|
|
Switching speed
|
200 ns, max.
|
|
Video input — XTP CP 4i DVI Pro
|
|
Number/signal type
|
4 digital RGB single link DVI-D (or HDMI*)
|
|
Connectors
|
4 female DVI-I (digital only)
|
|
Equalization
|
Automatic
|
|
Input cable length
|
>100' (30 m) at 1920x1200 @ 48, 50, or 60 Hz; or 1080p; 8 bit color
|
|
NOTE
|
The transmission distance varies depending on the signal resolution and on the type
of cable, graphics card, and display used in the system.
|
|
|
Video output — XTP CP 4o DVI Pro
|
|
Number/signal type
|
4 digital RGB single link DVI-D (or HDMI*)
|
|
Connectors
|
4 DVI-I (digital only)
|
|
Re-clocking
|
Automatic
|
|
Peripheral device power
|
5 VDC, 250 mA per output
|
|
Video — XTP CP 4i HDMI, XTP CP 4i HDMI DMA, XTP CP 4o HDMI
|
|
NOTE
|
*Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output.
|
|
|
Gain
|
Unity
|
|
Resolution range
|
Up to 1080p (HDTV) or 1920x1200 (the highest resolution of the single link DVI standard) @ 60 Hz
|
|
Signal type
|
Single-link HDMI (or DVI-D*)
|
|
Digital video
|
RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component
video (HDMI), actively buffered (supports all single-link DVI (if using an optional adapter) and HDMI standards from 640x480 @ 60 Hz to 1920x1200 @ 60 Hz)
|
|
Consumer Electronics Control (CEC)
|
Not supported
|
|
EDID and DDC
|
Supports Extended Display Identification Data (EDID) and Display Data
Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered.
|
|
HDCP
|
Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI 1.3 standards
|
|
HPD
|
Supports hot plug detection (HPD) of display as a pass-through signal.
|
|
Maximum data rate
|
6.75 Gbps (2.25 Gbps per color)
|
|
Maximum pixel clock
|
165 MHz
|
|
Standards
|
DVI 1.0, HDMI 1.3, HDCP 1.1
|
|
Switching speed
|
200 ns, max.
|
|
Video input — XTP CP 4i HDMI, XTP CP 4i HDMI DMA
|
|
Number/signal type
|
4 digital RGB single-link HDMI (or DVI-D*)
|
|
Connectors
|
4 female HDMI type A
|
|
Equalization
|
Automatic
|
|
Input cable length
|
>100' (30 m) at 1920x1200 @ 48, 50, or 60 Hz; or 1080p; 8 bit color
|
|
NOTE
|
The transmission distance varies depending on the signal resolution and on the type
of cable, graphics card, and display used in the system.
|
|
|
Video output — XTP CP 4o HDMI
|
|
Number/signal type
|
4 digital RGB single-link HDMI (or DVI-D*)
|
|
Connectors
|
4 female HDMI type A
|
|
Re-clocking
|
Automatic
|
|
Peripheral device power
|
5 VDC, 250 mA per output
|
|
Audio input — XTP CP 4i DMA, XTP CP 4i HDMI DMA
|
|
Source formats
|
PCM, Dolby Digital 2/0, Dolby Digital 2/0 Surround, Dolby Digital 5.1,
Dolby Digital EX, DTS Digital Surround 5.1, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1
|
|
Audio — XTP CP 4i VGA, XTP CP 4o SA
|
|
Gain
|
Unbalanced output: -6 dB; balanced output 0 dB
|
|
Frequency response
|
20 Hz to 20 kHz, ±0.05 dB
|
|
THD + Noise
|
0.03% @ 1 kHz at nominal level
|
|
S/N
|
>90 dB at maximum output (21 dBu, unweighted) (balanced)
|
|
Crosstalk
|
<-80 dB @ 1 kHz, fully loaded
|
Stereo channel separation
|
>80 dB @ 1 kHz
|
|
CMRR
|
>75 dB @ 20 Hz to 20 kHz
|
|
Audio input — XTP CP 4i VGA
|
|
Number/signal type
|
4 stereo, balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm captive screw connector, 5 pole
|
|
Impedance
|
>10k ohms unbalanced/balanced, DC coupled
|
|
Nominal level
|
0 dBu (0.775 Vrms)
|
|
Maximum level
|
+19.5 dBu, (balanced or unbalanced) at 1% THD+N
|
|
Input gain adjustment
|
-18 dB to +18 dB, adjustable per input; default = 0 dB
|
|
NOTE
|
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
|
|
|
Audio output — XTP CP 4o SA
|
|
Number/signal type
|
4 stereo, balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm captive screw connector, 5 pole
|
|
Impedance
|
50 ohms unbalanced, 100 ohms balanced
|
|
Gain error
|
±0.1 dB channel to channel
|
|
Maximum level (Hi-Z)
|
>+21 dBu, balanced or unbalanced at 0.1% THD+N
|
|
Maximum level (600 ohm)
|
>+15 dBm, balanced or unbalanced at 0.1% THD+N
|
|
Volume
control range
|
-98 dB to 0 dB (volume numbers 0 through 64) in a 35 dB increment from step
0 to step 1, then in 1 dB increments from steps 1 to 64; default = 64 (0 dB)
|
|
NOTE
|
Attenuation = volume number minus 64. The default is 0 dB = volume number 64.
|
|
|
Audio — XTP CP 4i DVI Pro, XTP CP 4o DVI Pro, XTP CP 4i HDMI, XTP CP 4o HDMI
|
|
Gain
|
Unbalanced output: -6 dB; balanced output 0 dB
|
|
Frequency response
|
20 Hz to 20 kHz, ±0.05 dB
|
|
THD +
Noise
|
0.01% @ 1 kHz at nominal level
|
|
S/N
|
>105 dB at maximum output (21 dBu, unweighted) (balanced)
|
|
Crosstalk
|
<-89 dB @ 1 kHz, fully loaded
|
|
Stereo
channel separation
|
>105 dB @ 1 kHz
|
|
CMRR
|
>83 dB @ 20 Hz to 20 kHz
|
|
Audio input — XTP CP 4i DVI Pro, XTP CP 4i HDMI
|
|
Number/signal type
|
4 stereo, balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm captive screw connector, 5 pole
|
|
Impedance
|
>10k ohms unbalanced/balanced, DC coupled
|
|
Nominal
level
|
+4 dBu (1.228 Vrms)
|
|
Maximum
level
|
+21 dBu, (balanced or unbalanced) at 0.01% THD+N
+19.5 dBu, (balanced or unbalanced) at 1% THD+N
|
|
Input
gain adjustment
|
-18 dB to +18 dB, adjustable per input; default = 0 dB
|
|
Audio output — XTP CP 4o DVI Pro, XTP CP 4o HDMI
|
|
Number/signal type
|
4 stereo, balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm captive screw connector, 5 pole
|
|
Impedance
|
50 ohms unbalanced, 100 ohms balanced
|
|
Gain
error
|
±0.1 dB channel to channel
|
|
Maximum
level (Hi-Z)
|
>+21 dBu, balanced or unbalanced at 1% THD+N
|
|
Maximum
level (600 ohm)
|
>+20 dBm, balanced or unbalanced at 1% THD+N
|
|
Volume
control range
|
-75.8 dB to 0 dB (volume numbers 0 through 64) in a 35 dB increment from
step 0 to step 1, then in 1 dB increments from steps 1 to 64; default = 64
(0 dB)
|
|
NOTE
|
Attenuation = volume number minus 64. The default is 0 dB = volume number 64.
|
|
|
Control/remote — switcher host ports
|
|
NOTE
|
The front
panel USB port and rear panel RS-232 port are independent of each other and can
be used at the same time.
|
|
|
Serial
host control port
|
1 bidirectional RS-232 or RS-422, rear panel female 9-pin D connector
|
|
Baud
rate and protocol
|
9600 (default) to 115200 baud, 8 data bits, 1 stop bit, no parity, no flow
control
|
|
Serial
control pin configurations
|
|
|
RS-232
|
2 = Tx, 3 = Rx, 5 = GND
|
|
RS-422
|
2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+
|
|
USB
control port
|
1 front panel female mini USB B
|
|
USB
standards
|
USB 2.0, low speed
|
|
Ethernet control port
|
1 female RJ-45
|
|
Ethernet data rate (for network communication)
|
10/100Base-T, half/full duplex with autodetect
|
|
Ethernet protocol
|
ARP, ICMP (ping), IP, TCP, DHCP, HTTP, SMTP, Telnet
|
|
Ethernet default settings
|
Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Default gateway = 0.0.0.0
DHCP = off
|
|
Web
server
|
Up to 200 simultaneous sessions
7.0 MB nonvolatile user memory
|
|
Program
control
|
Extron control/configuration
program for Windows®
Extron Simple Instruction
Set (SIS™)
Microsoft® Internet Explorer® ver. 6 or higher, Telnet
|
|
Control/remote — external device (pass-through, unidirectional or bidirectional)
|
|
Ethernet pass-through port
|
1 female RJ-45 connector
|
|
Ethernet data rate
|
10/100Base-T, half/full duplex with autodetect
|
|
General
|
|
Power
|
Internal
Input: 100-240 VAC, 50-60 Hz
|
|
XTP
CrossPoint 1600
|
Redundant power supply is optional.
|
|
XTP
CrossPoint 3200
|
Redundant power supply is standard.
|
|
Power
consumption
|
|
|
XTP
CrossPoint 1600
|
300 watts
|
|
XTP
CrossPoint 3200
|
500 watts
|
|
Individual I/O boards
|
TBD
|
|
Temperature/humidity
|
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
|
|
Cooling
|
Fan, left to right (as viewed from front panel)
|
|
Mounting
|
|
|
Rack
mount
|
Yes
|
|
Enclosure type
|
Metal
|
|
Enclosure dimensions (Depth excludes connectors. Width excludes rack ears.)
|
|
XTP
CrossPoint 1600
|
8.75" H x 17.0" W x 15.0" D (5U high, full rack wide)
(22.2 cm H x 43.2 cm W x 38.1 cm D)
|
|
XTP
CrossPoint 3200
|
17.5" H x 17.0" W x 17.5" D (10U high, full rack wide)
(44.5 cm H x 43.2 cm W x 44.5 cm D)
|
|
Product
weight with boards installed
|
|
|
XTP
CrossPoint 1600
|
18.1 lbs (8.3 kg)
|
|
XTP
CrossPoint 3200
|
33.4 lbs (15.2 kg)
|
|
Shipping weight with boards installed
|
|
|
XTP
CrossPoint 1600
|
23 lbs (11 kg)
|
|
XTP
CrossPoint 3200
|
42 lbs (20 kg)
|
|
Shipping weight of individual boards, if purchased separately
|
2 lbs (1 kg)
|
|
DIM
weight
|
|
|
XTP
CrossPoint 1600
|
25 lbs (12 kg)
|
|
XTP
CrossPoint 3200
|
44 lbs (20 kg)
|
|
Vibration
|
ISTA 1A in carton (International Safe Transit Association)
|
|
Regulatory compliance
|
|
|
Safety
|
CE, c-UL, UL
|
|
EMI/EMC
|
CE, C-tick, FCC Class A, ICES, VCCI
|
|
MTBF
|
30,000 hours
|
|
Warranty
|
3 years parts and labor
|
|
NOTE
|
All nominal levels are at ±10%.
|
|
