|
Extron XTP Cross Point 1600 Series - Modular Digital
Matrix Switchers from 4x4 to 16x16 |
Product
Code:XTPCP1600SERIES
 |
Extron Matrix Switchers
< HDMI Matrix Switchers
<
DVI Matrix Switchers |
The Extron XTP CrossPoint 1600
provides flexible, reliable digital and analog video switching and
distribution between local and remote endpoints. This modular
matrix switcher is configurable from 4x4 up to 16x16 using a wide
variety of available input and output boards. It sends
high-resolution video, audio, RS-232, Ethernet, and power up to 330
feet (100 m) over a shielded CATx cable to remote XTP®
transmitters and receivers. The XTP CrossPoint 1600 also supports
direct HDMI, DVI, VGA, video, and audio connections to local
sources and displays. XTP Systems® deliver robust signal
routing and reliability with ultra-fast digital video switching and
advanced system monitoring.
XTP Systems are HDCP compliant and delivers ultra-fast, highly
reliable digital switching with Extron exclusive SpeedSwitch®
Technology. They include a wide range of integrator-friendly
features such as EDID Minder®, Key Minder®, and advanced
system monitoring and control capability.
An Extron XTP CrossPoint® matrix switcher is the heart of XTP
Systems. The high speed, 15.2 Gbps data-rate digital backplane
designed into the matrix switcher ensures full compatibility with
the highest resolution signals currently in use, while also
providing a future-ready upgrade path for new formats with higher
resolutions such as 4K and Ultra HD - UHD video. Its modular design
allows the system to be customized to the application, with
available input and output boards providing local distribution of
HDMI, DVI, VGA, video, and audio connections in addition to
long-distance transmission to and from remote XTP transmitters and
receivers. Each XTP board is hot-swappable so that the matrix
switcher can be serviced or reconfigured without interrupting
signal routing. Unoccupied board slots can be reserved for future
system expansion.
XTP Systems also provide extensive audio signal routing and
management features. Some of these features include integrating
analog stereo audio alongside digital HDMI audio, HDMI audio
embedding and de-embedding, audio breakaway, and downmixing
multi-channel formats. In addition, the system can provide
extension of Ethernet plus RS-232 and IR over the same shielded
twisted pair cable as used for high resolution video and audio
signal transmission. The use of a single twisted pair cable for
multiple signals streamlines device operation and control,
simplifies a cabling infrastructure, and reduces the need for added
network drops.
Extron recommends Extron-certified XTP DTP 24 shielded twisted pair
cable, shielded RJ-45 plugs, jacks, and couplers engineered for
optimum signal transmission with Extron XTP Systems. The XTP DTP 24
cable is certified to 475 MHz, and utilizes a SF/UTP design with
four unshielded 24 AWG twisted pair conductors inside an overall
braid and foil shield for superior performance and noise
immunity.
Easy Setup and
Configuration
The XTP CrossPoint matrix switcher provides convenient,
user-friendly control software, for configuring, operating, and
monitoring the system. It includes many of the features common to
Extron matrix switchers such as I/O memory presets and the
QS-FPC™ - QuickSwitch Front Panel Controller with tri-color
backlit buttons.
To enhance and simplify integration of digital and analog AV
devices, the matrix switcher utilizes two Extron-exclusive
technologies: EDID Minder and Key Minder. EDID Minder automatically
manages EDID communication between all connected input sources.
This technology allows EDID from any of the displays, or pre-stored
selectable EDID information, to be assigned to any input. By
maintaining continuous EDID communication with all sources, EDID
Minder ensures that sources power up properly and reliably send
content to the displays. For HDMI signals with protected content,
Key Minder authenticates and maintains continuous HDCP encryption
between input and output devices to ensure reliable switching while
enabling simultaneous distribution of a single source signal to one
or more displays. If an HDCP-encrypted signal is routed to a
non-compliant display, a full-screen green signal is transmitted to
the destination, providing immediate visual confirmation that
protected content cannot be viewed on the selected display.
With the included software, EDID communication can easily be set
for all devices. The software provides a complete view of the
matrix switcher and remote XTP transmitters and receivers, and
facilitates control and real-time status monitoring of all XTP
devices through a computer.
System Monitoring and
Control
The XTP CrossPoint matrix switcher can be controlled via RS-232,
Ethernet, and the USB port on the front panel. With the capability
to transmit control signals over the same CATx cabling as for AV,
XTP Systems provide considerable flexibility to control the entire
system. Bidirectional RS-232 signals can be inserted from a control
system into the Ethernet port on the matrix switcher, enabling
RS-232 control of devices attached to XTP transmitters and
receivers.
Bidirectional RS-232 and IR insertion ports are included on the XTP
CP input and output boards, transmitters, and receivers. These
insertion ports allow, for example, a control system to insert IR
signals into an XTP CP input board. The signals are then
communicated to an XTP transmitter for controlling a Blu-ray Disc
player. Similarly, the same control system can also insert RS-232
signals into an XTP CP output board for relay to an XTP receiver
interfaced with a display device. All of this flexible system
control capability is available using the same CATx cable to send
control signals, alongside AV and Ethernet. The end result is a
simplified wiring infrastructure that reduces costs and labor.
Extend Ethernet to
Expand Network Access and AV Device Control
An Ethernet port accompanies each XTP RJ-45 port on an XTP
transmitter or receiver, and the XTP CP input and output boards.
These ports can be used to extend Ethernet access from the matrix
switcher to remote endpoints over the same CATx cable, without the
need to provide additional network drops or switches. For example,
Blu-ray Disc players at the source endpoints can receive Internet
access from the house LAN that is interfaced into the Ethernet
ports of an XTP CP input board. A separate LAN for the control
system can be used to control remote displays via the Ethernet
ports on the XTP CP output boards.
The Ethernet ports on the XTP CP input and output boards can also
be connected into a shared house LAN for both system control and
network access. This also allows control system devices to be
situated at remote endpoints. The capability to extend Ethernet to
remote endpoints provides substantial flexibility to set LAN access
in accordance with end-user requirements and IT policy.
Power
Capabilities
As an added feature, the matrix switcher is capable of providing
power to remote XTP devices using the same cable that transmits
high resolution video, audio, RS-232 or IR, and Ethernet. The use
of a single cable for AV, control, and power simplifies endpoint
integration. The XTP CrossPoint 1600 rack-mountable 5U enclosure
also allows for the addition of an optional redundant power supply,
ensuring continuous operation in mission-critical
installations.
With hot-swappable modular components, a wide selection of XTP
transmitters and receivers, and advanced 24/7 system monitoring,
the XTP CrossPoint 1600 is designed to provide continuous,
trouble-free operation in the most critical applications.
|
• Available
in I/O sizes from 4x4 to 16x16 — System configuration is
flexible to match a wide variety of small to large-sized
installations.
• 15.2 Gbps data-rate digital backplane — Ensures
switching and distribution of video signals without degradation,
offering the performance required to maintain signal integrity with
the most demanding high resolution signals.
• Compatible with all XTP integrated system products —
XTP Systems provide flexible, reliable signal switching and
distribution in an integrated solution for multiple digital and
analog formats.
• Fully digital signal routing — Analog signals are
digitized, sending a reliable, high quality digital video signal to
the output destination.
• Wide selection of input and output boards — Boards
provide integration for a variety of signal types and formats,
ensuring system customization appropriate for a wide range of
applications.
• RS-232 insertion from the Ethernet control port —
System level device control to all remote locations via the matrix
switcher's Ethernet port, providing comprehensive control of
endpoints and attached devices without needing additional
cabling.
• Remote power to XTP transmitters and receivers — To
simplify installation in space-challenged locations, an XTP
CrossPoint matrix switcher can provide power to remote XTP
transmitters and receivers over the same CATx cable as used for
sending AV signals. This avoids the need to separately power XTP
devices at remote endpoints.
• Supported HDMI specification features include data rates up
to 6.75 Gbps, Deep Color up to 12-bit, 3D, and HD lossless audio
formats
• HDCP compliant — Ensures display of content-protected
media and interoperability with other HDCP-compliant devices.
• SpeedSwitch® Technology provides exceptional switching
speed for HDCP-encrypted content
• SD Pro processing provides deinterlacing of standard
definition video — SD Pro processing deinterlaces 480i and
576i signals for compatibility with HDMI and DVI-equipped displays,
without the need for additional scalers.
• EDID Minder® automatically manages EDID communication
between connected devices — EDID Minder ensures that all
sources power up properly and reliably output content for
display.
• Key Minder® continuously verifies HDCP compliance for
quick, reliable switching — Key Minder authenticates and
maintains continuous HDCP encryption between input and output
devices to ensure quick and reliable switching in professional AV
environments, while enabling simultaneous distribution of a single
source to multiple displays.
• Automatic color bit depth management — The switcher
automatically adjusts color bit depth output based on the display
EDID, preventing color compatibility conflicts between source and
display.
• HDMI to DVI Interface Format Correction —
Automatically reformats HDMI source signals for output to a
connected DVI display.
• Modular, field-upgradeable and hot-swappable design —
The XTP CrossPoint matrix switcher provides substantial
flexibility, expandability, and affordability by allowing users to
select the configuration required for a system. Additional input
and output boards may be added at any time for quick and easy
upgradeability or expansion. Hot-swappable components allow the
user to replace an I/O board at any time without the need to power
down the switcher. This is especially useful for mission-critical
applications that require continuous system operation.
• Audio breakaway — Provides the capability to separate
an embedded audio signal from its corresponding video signal within
the matrix switcher, allowing the audio and video signals from one
source to be switched to different destinations.
• Ethernet extension — Centralized 10/100 Ethernet
communication can be implemented via an Ethernet pass-through port
to reduce the amount of independent network drops required within a
system.
• HDMI and DVI output boards provide +5 VDC, 250 mA power on
each output for powering external peripheral devices — Power
provided via a board's digital output eliminates the need of a
separate power supply for the connected peripheral device.
• Automatic cable equalization for each digital input to 100
feet (30 m) when used with Extron HDMI/DVI Pro cables — Cable
input equalization optimizes signal performance for all incoming
signals, ensuring pristine image quality is delivered throughout
XTP Systems.
• Automatic output reclocking — Reshapes and restores
timing of digital video signals at each output, eliminating high
frequency jitter to ensure reliable transmission over long
cables.
• HDCP authentication and signal presence confirmation via
RS-232 or Ethernet — Provides real-time verification of HDCP
status for each digital video input and output. This allows for
simple, quick, and easy signal and HDCP verification through
RS-232/RS-422 or Ethernet, providing valuable feedback to a system
operator or helpdesk support staff.
• HDCP Visual Confirmation provides a green signal when
encrypted content is sent to a non-compliant display — A
full-screen green signal is sent when HDCP-encrypted content is
transmitted to a non-HDCP compliant display, providing immediate
visual confirmation that protected content cannot be viewed on the
display.
• Audio input gain and attenuation — Allows the level
of gain or attenuation to be set, eliminating noticeable volume
differences when switching between sources.
• Audio output volume adjustment and muting — Audio
output can be set dynamically for each channel through the front
panel or serial control eliminating the need for audio
preamplifiers in many system designs.
• Ethernet monitoring and control — Engineered to meet
the needs of professional AV environments, Ethernet control
provides proactive monitoring and system management over a LAN,
WAN, or the Internet, using standard TCP/IP protocols. Ethernet
control provides for remote selection of input and output ties,
adjustment and control of audio input and output levels, and
advanced system diagnostics.
• Optional redundant power supply — An optional
redundant power supply is available for the XTP CrossPoint 1600 for
continuous, mission-critical applications where power reliability
is crucial.
• Tri-color, backlit buttons — Buttons can be custom
labeled for easy identification. The buttons illuminate red, green,
or amber, depending on function, for ease of use in low-light
environments.
• QS-FPC™ - QuickSwitch Front Panel Controller —
Provides a discrete button for each input and output, allowing for
simple, intuitive operation.
• Global presets — Frequently used I/O configurations
may be saved and recalled either from the front panel, serial, or
Ethernet control. This time-saving feature allows I/O
configurations to be set up and stored in memory for future
use.
• View I/O mode — Users can easily view which inputs
and outputs are actively connected.
• Front panel configuration port — Enables easy
configuration without having to access the matrix switcher's rear
panel.
• Front panel security lockout — Prevents unauthorized
use in non-secure environments. In lockout mode, a special button
combination is required to operate the matrix switcher from the
front panel controller.
• Optional remote control — The optional MKP 2000 and
MKP 3000 X-Y Remote Control Panels provide the flexibility to
control the matrix switcher from a remote location.
• Rack-mountable 5U, full rack width metal enclosure
• Highly reliable, energy-efficient internal universal power
supply — The 100-240 VAC, 50/60 Hz, international power
supply provides worldwide power compatibility with high
demonstrated reliability.
|
|
Video input — XTP
CP 4i, XTP CP 4i DMA
|
|
Number/signal
type
|
4 sets of
proprietary twisted pair AV signals
|
|
Connectors
|
4 female RJ-45
per board
|
|
NOTE
|
Input comes
from an Extron XTP Series twisted
pair transmitter.
|
|
|
Control/remote
— external device (pass-through, unidirectional or
bidirectional)
|
|
Serial
control port input/output
|
1 set of
proprietary signals on a female RJ-45 jack
|
|
Serial
control port output/input
|
RS-232 (+5) via
(1) 3.5 mm, 5-pole captive screw connector (uses 3 poles)
(connector is shared with IR control port)
|
|
Baud
rates
|
Up to 115200
baud
|
|
Protocol
|
Data bits = 5 -
8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
|
|
Serial
control pin configuration
|
1 = Tx, 2 = Rx,
3 = GND
|
|
Ethernet
pass-through port
|
1 female RJ-45
connector
|
|
Ethernet
data rate
|
10/100Base-T,
half/full duplex with autodetect
|
|
IR
control port
|
(1) 3.5 mm,
captive screw connector, 5 pole (connector is shared with RS-232
control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to
40 kHz
|
|
IR
control pin configuration
|
3 = GND, 4 = IR
Tx, 5 = IR Rx
|
|
Video output —
XTP CP 4o
|
|
Number/signal
type
|
4 sets of
proprietary twisted pair AV signals
|
|
Connectors
|
4 female RJ-45
per board
|
|
NOTE
|
Output connects to an
Extron XTP Series twisted pair receiver.
|
|
|
Control/remote
— external device (pass-through, unidirectional or
bidirectional)
|
|
Serial
control port input/output
|
1 set of
proprietary signals on a female RJ-45 jack
|
|
Serial
control port output/input
|
RS-232 (+5) via
(1) 3.5 mm, 5-pole captive screw connector (uses 3 poles)
(connector is shared with IR control port)
|
|
Baud
rates
|
Up to 115200
baud
|
|
Protocol
|
Data bits = 5 -
8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
|
|
Serial
control pin configuration
|
1 = Tx, 2 = Rx,
3 = GND
|
|
Ethernet
pass-through port
|
1 female RJ-45
connector
|
|
Ethernet
data rate
|
10/100Base-T,
half/full duplex with autodetect
|
|
IR
control port
|
(1) 3.5 mm,
captive screw connector, 5 pole (connector is shared with RS-232
control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to
40 kHz
|
|
IR
control pin configuration
|
3 = GND, 4 = IR
Tx, 5 = IR Rx
|
|
Video — XTP CP 4i
VGA
|
|
Gain
|
Unity
|
|
Analog
resolution range
|
Up to
1920x1200* or 1080p (HDTV)
*reduced blanking
|
|
Bandwidth
|
300 MHz (-3
dB), fully loaded
0-10 MHz: no more than +0.1 dB to -0.1 dB
0-130 MHz: no more than +0.8 dB to -0.8 dB
|
|
Crosstalk
|
-88 dB @ 1 MHz,
-55 dB @ 10 MHz, -45 dB @ 30 MHz, -37 dB @ 100 MHz
|
|
Switching
speed
|
200 ms
(max.)
|
|
Video input — XTP
CP 4i VGA
|
|
Number/signal
type
|
4 analog
VGA-QXGA RGBHV, RGBS, RGsB, RsGsBs, HDTV, component video, S-video,
composite video
|
|
Connectors
|
4 female
15-pin HD
|
|
Nominal
level
|
1 Vp-p for Y of
component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
|
|
Minimum/maximum
levels
|
Analog: 0.5 V
to 2.0 Vp-p with no offset
|
|
Impedance
|
75
ohms
|
|
Return
loss
|
>30 dB @ 5
MHz
|
|
DC
offset (max. allowable)
|
1.5
V
|
|
Video processing
— XTP CP 4i VGA
|
|
Decoder
|
8 bit
digital
|
|
Digital
sampling
|
30 bit, 10 bits
per color; 162 MHz standard
|
|
Colors
|
1
billion
|
|
Sync — XTP CP 4i
VGA
|
|
Input
type
|
RGBHV, RGBS,
RGsB, RsGsBs
|
|
Input
level
|
0.5 V to 5.0
Vp-p, 4.0 Vp-p normal
|
|
Input
impedance
|
510
ohms
|
|
Horizontal
frequency
|
30 kHz to 100
kHz
|
|
Vertical
frequency
|
24 Hz to 120
Hz
|
|
Max.
propagation delay
|
30
ns
|
|
Max.
rise/fall time
|
4
ns
|
|
Polarity
|
Positive or
negative
|
|
Video — XTP
CP 4i DVI Pro, XTP CP 4o DVI Pro
|
|
NOTE
|
*Appropriate DVI-D to
HDMI cables or adapters are required for HDMI signal
input/output.
|
|
|
Gain
|
Unity
|
|
Resolution
range
|
Up to
1920x1200*, 2k, or 1080p @ 60 Hz
*Reduced blanking
|
|
Signal
type
|
Single link DVI
digital video signals are supported.
|
|
Digital
video
|
RGB digital
video (DVI and HDMI standards) or Y, Cr, Cb digital component video
(HDMI), actively buffered (supports all single link DVI and HDMI
(if using an optional adapter) standards from 640x480 @ 60 Hz to
1920x1200 @ 60 Hz computer video) or 2k
|
|
NOTE
|
These XTP CP DVI Pro
boards are compatible with HDMI.
|
|
|
Digital
audio
|
Supports HDMI
audio (if using an HDMI to DVI adapter) transmitted through the RGB
and Y, Cr, Cb lines, actively buffered.
|
|
Consumer
Electronics Control (CEC)
|
Not
supported
|
|
EDID
and DDC
|
Supports
Extended Display Identification Data (EDID) and Display Data
Channel (DDC) data using DVI and HDMI standards. EDID and DDC
signals are actively buffered.
|
|
HDCP
|
Compliant with
High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI
standards
|
|
HPD
|
Supports hot
plug detection (HPD) of display as a pass-through
signal.
|
|
Maximum
data rate
|
6.75 Gbps (2.25
Gbps per color)
|
|
Maximum
pixel clock
|
165
MHz
|
|
Standards
|
DVI 1.0, HDMI,
HDCP 1.1
|
|
Switching
speed
|
200 ns,
max.
|
|
Video input — XTP
CP 4i DVI Pro
|
|
Number/signal
type
|
4 digital RGB
single link DVI-D (or HDMI*)
|
|
Connectors
|
4 female DVI-I
(digital only)
|
|
Equalization
|
Automatic
|
|
Input
cable length
|
>100' (30 m)
at 1920x1200, 2k, or 1080p @ 60 Hz
|
|
NOTE
|
The transmission
distance varies depending on the signal resolution and on the type
of cable, graphics card, and display used in the
system.
|
|
|
Video output —
XTP CP 4o DVI Pro
|
|
Number/signal
type
|
4 digital RGB
single link DVI-D (or HDMI*)
|
|
Connectors
|
4 DVI-I
(digital only)
|
|
Re-clocking
|
Automatic
|
|
Peripheral
device power
|
5 VDC, 250 mA
per output
|
|
Video — XTP CP 4i
HDMI, XTP CP 4i HDMI DMA, XTP CP 4o HDMI
|
|
NOTE
|
*Appropriate HDMI
to DVI-D cables or adapters are required for DVI signal
input/output.
|
|
|
Gain
|
Unity
|
|
Resolution
range
|
Up to
1920x1200*, 2k, or 1080p @ 60 Hz
*Reduced blanking
|
|
Signal
type
|
Single-link
HDMI (or DVI-D*)
|
|
Digital
video
|
RGB digital
video (DVI and HDMI standards) or Y, Cr, Cb digital component video
(HDMI), actively buffered (supports all single-link DVI (if using
an optional adapter) and HDMI standards from 640x480 @ 60 Hz to
1920x1200 @ 60 Hz) or 2k
|
|
Consumer
Electronics Control (CEC)
|
Not
supported
|
|
EDID
and DDC
|
Supports
Extended Display Identification Data (EDID) and Display Data
Channel (DDC) data using DVI and HDMI standards. EDID and DDC
signals are actively buffered.
|
|
HDCP
|
Compliant with
High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI
standards
|
|
HPD
|
Supports hot
plug detection (HPD) of display as a pass-through
signal.
|
|
Maximum
data rate
|
6.75 Gbps (2.25
Gbps per color)
|
|
Maximum
pixel clock
|
165
MHz
|
|
Standards
|
DVI 1.0, HDMI,
HDCP 1.1
|
|
Switching
speed
|
200 ns,
max.
|
|
Video input — XTP
CP 4i HDMI, XTP CP 4i HDMI DMA
|
|
Number/signal
type
|
4 digital RGB
single-link HDMI (or DVI-D*)
|
|
Connectors
|
4 female HDMI
type A
|
|
Equalization
|
Automatic
|
|
Input
cable length
|
>100' (30 m)
at 1920x1200, 2k, or 1080p @ 60 Hz
|
|
NOTE
|
The transmission
distance varies depending on the signal resolution and on the type
of cable, graphics card, and display used in the
system.
|
|
|
Video output —
XTP CP 4o HDMI
|
|
Number/signal
type
|
4 digital RGB
single-link HDMI (or DVI-D*)
|
|
Connectors
|
4 female HDMI
type A
|
|
Re-clocking
|
Automatic
|
|
Peripheral
device power
|
5 VDC, 250 mA
per output
|
|
Audio input — XTP
CP 4i DMA, XTP CP 4i HDMI DMA
|
|
Supported
formats — Pass through / down mix
|
|
XTP/HDMI
connector
|
LPCM up to
7.1/24-bit/192kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital
EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital
2/0, DTS-HD Master Audio, DTS-HD, DTS ES Discrete 6.1, DTS ES
Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
|
|
Analog
connector
|
Analog stereo
audio
|
|
Audio — XTP CP 4i
VGA, XTP CP 4o SA
|
|
Gain
|
Unbalanced
output: -6 dB; balanced output 0 dB
|
|
Frequency
response
|
20 Hz to 20
kHz, ±0.05 dB
|
|
THD +
Noise
|
0.03% @ 1 kHz
at nominal level
|
|
S/N
|
>90 dB at
maximum output (21 dBu, unweighted) (balanced)
|
|
Crosstalk
|
<-80 dB @ 1
kHz, fully loaded
|
|
Stereo
channel separation
|
>80 dB @ 1
kHz
|
|
CMRR
|
>75 dB @ 20
Hz to 20 kHz
|
|
Audio input — XTP
CP 4i VGA
|
|
Number/signal
type
|
4 stereo,
balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm
captive screw connector, 5 pole
|
|
Supported
formats
|
Analog stereo
audio
|
|
Impedance
|
>10k ohms
unbalanced/balanced, DC coupled
|
|
Nominal
level
|
0 dBu (0.775
Vrms)
|
|
Maximum
level
|
+19.5 dBu,
(balanced or unbalanced) at 1% THD+N
|
|
Input
gain adjustment
|
-18 dB to +18
dB, adjustable per input; default = 0 dB
|
|
NOTE
|
0 dBu = 0.775 Vrms, 0
dBV = 1 Vrms, 0 dBV ≈ 2 dBu
|
|
|
Audio output —
XTP CP 4o SA
|
|
Number/signal
type
|
4 stereo,
balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm
captive screw connector, 5 pole
|
|
Supported
formats
|
Analog stereo
audio
|
|
Impedance
|
50 ohms
unbalanced, 100 ohms balanced
|
|
Gain
error
|
±0.1 dB
channel to channel
|
|
Maximum
level (Hi-Z)
|
>+21 dBu,
balanced or unbalanced at 0.1% THD+N
|
|
Maximum
level (600 ohm)
|
>+15 dBm,
balanced or unbalanced at 0.1% THD+N
|
|
Volume
control range
|
-98 dB to 0 dB
(volume numbers 0 through 64) in a 35 dB increment from step 0 to
step 1, then in 1 dB increments from steps 1 to 64; default = 64
(0 dB)
|
|
NOTE
|
Attenuation = volume
number minus 64. The default is 0 dB = volume number
64.
|
|
|
Audio — XTP CP 4i
DVI Pro, XTP CP 4o DVI Pro, XTP CP 4i HDMI, XTP CP 4o
HDMI
|
|
Gain
|
Unbalanced
output: -6 dB; balanced output 0 dB
|
|
Frequency
response
|
20 Hz to 20
kHz, ±0.05 dB
|
|
THD +
Noise
|
0.01% @ 1 kHz
at nominal level
|
|
S/N
|
>105 dB at
maximum output (21 dBu, unweighted) (balanced)
|
|
Crosstalk
|
<-89 dB @ 1
kHz, fully loaded
|
|
Stereo
channel separation
|
>105 dB @ 1
kHz
|
|
CMRR
|
>83 dB @ 20
Hz to 20 kHz
|
|
Audio input — XTP
CP 4i DVI Pro, XTP CP 4i HDMI
|
|
Number/signal
type
|
4 stereo,
balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm
captive screw connector, 5 pole
|
|
Supported
formats — Pass through
|
|
|
HDMI/DVI
Pro connector
|
LPCM up to
7.1/24-bit/192kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital
EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital
2/0, DTS-HD Master Audio, DTS-HD, DTS ES Discrete 6.1, DTS ES
Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
|
|
Analog
connector
|
Analog stereo
audio
|
|
Impedance
|
>10k ohms
unbalanced/balanced, DC coupled
|
|
Nominal
level
|
+4 dBu (1.228
Vrms)
|
|
Maximum
level
|
+21 dBu,
(balanced or unbalanced) at 0.01% THD+N
+19.5 dBu, (balanced or unbalanced) at 1% THD+N
|
|
Input
gain adjustment
|
-18 dB to +18
dB, adjustable per input; default = 0 dB
|
|
Audio output —
XTP CP 4o DVI Pro, XTP CP 4o HDMI
|
|
Number/signal
type
|
4 stereo,
balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm
captive screw connector, 5 pole
|
|
Supported
formats — Pass through
|
|
|
HDMI/DVI
Pro connector
|
LPCM up to
7.1/24-bit/192kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital
EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital
2/0, DTS-HD Master Audio, DTS-HD, DTS ES Discrete 6.1, DTS ES
Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
|
|
Analog
connector
|
Analog stereo
audio
|
|
Impedance
|
50 ohms
unbalanced, 100 ohms balanced
|
|
Gain
error
|
±0.1 dB
channel to channel
|
|
Maximum
level (Hi-Z)
|
>+21 dBu,
balanced or unbalanced at 1% THD+N
|
|
Maximum
level (600 ohm)
|
>+20 dBm,
balanced or unbalanced at 1% THD+N
|
|
Volume
control range
|
-75.8 dB to 0
dB (volume numbers 0 through 64) in a 35 dB increment from step 0
to step 1, then in 1 dB increments from steps 1 to 64; default = 64
(0 dB)
|
|
NOTE
|
Attenuation = volume
number minus 64. The default is 0 dB = volume number
64.
|
|
|
Control/remote —
switcher host ports
|
|
NOTE
|
The front panel USB
port and rear panel RS-232 port are independent of each other and
can be used at the same time.
|
|
|
Serial
host control port
|
1 bidirectional
RS-232 or RS-422, rear panel female 9-pin D
connector
|
|
Baud
rate and protocol
|
9600 (default)
to 115200 baud, 8 data bits, 1 stop bit, no parity, no flow
control
|
|
Serial
control pin configurations
|
|
RS-232
|
2 = Tx, 3 = Rx,
5 = GND
|
|
RS-422
|
2 = Tx-, 3 =
Rx-, 5 = GND, 7 = Rx+, 8 = Tx+
|
|
USB
control port
|
1 front panel
female mini USB B
|
|
USB
standards
|
USB 2.0, low
speed
|
|
Ethernet
control port
|
1 female
RJ-45
|
|
Ethernet
data rate (for network communication)
|
10/100Base-T,
half/full duplex with autodetect
|
|
Ethernet
protocol
|
ARP, ICMP
(ping), IP, TCP, DHCP, HTTP, SMTP, Telnet
|
|
Ethernet
default settings
|
Link speed and
duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Default gateway = 0.0.0.0
DHCP = off
|
|
Web
server
|
Up to 200
simultaneous sessions
7.0 MB nonvolatile user memory
|
|
Program
control
|
Extron XTP
System Configuration Software for Windows®
Extron Simple Instruction Set (SIS™)
Microsoft® Internet Explorer® ver. 6 or higher,
Telnet
|
|
General
|
|
Power
|
Internal
Input: 100-240 VAC, 50-60 Hz
|
|
XTP
CrossPoint 1600
|
Redundant power
supply is optional.
|
|
XTP
CrossPoint 3200
|
Redundant power
supply is standard.
|
|
Power
consumption
|
|
XTP
CrossPoint 1600
|
50 to 810
watts, depending on configuration
|
|
XTP
CrossPoint 3200
|
100 to 1200
watts, depending on configuration
|
|
Individual
I/O boards
|
TBD
|
|
Remote
power capability
|
|
XTP
CrossPoint 1600
|
Supports up to
28 endpoints
|
|
XTP
CrossPoint 3200
|
Supports up to
24 endpoints.
|
|
Temperature/humidity
|
Storage: -40 to
+158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%,
noncondensing
|
|
Cooling
|
Fan, right to
left (as viewed from front panel)
|
|
Mounting
|
|
Rack
mount
|
Yes
|
|
Enclosure
type
|
Metal
|
|
Enclosure
dimensions (Depth excludes connectors. Width excludes rack
ears.)
|
|
XTP
CrossPoint 1600
|
8.75" H x 17.0"
W x 17.5" D (5U high, full rack wide)
(22.2 cm H x 43.2 cm W x 44.5 cm D)
|
|
XTP
CrossPoint 3200
|
17.5" H x 17.0"
W x 17.5" D (10U high, full rack wide)
(44.5 cm H x 43.2 cm W x 44.5 cm D)
|
|
Product
weight with boards installed
|
|
XTP
CrossPoint 1600
|
39.0 lbs (17.7
kg)
|
|
XTP
CrossPoint 3200
|
59.0 lbs (26.8
kg)
|
|
Shipping
weight with boards installed
|
|
XTP
CrossPoint 1600
|
48 lbs (22
kg)
|
|
XTP
CrossPoint 3200
|
71 lbs (33
kg)
|
|
Shipping
weight of individual boards, if purchased
separately
|
2 lbs (1
kg)
|
|
DIM
weight
|
|
XTP
CrossPoint 1600
|
|
International
|
53 lbs (24
kg)
|
|
XTP
CrossPoint 3200
|
|
USA/Canada
|
76 lbs (35
kg)
|
|
International
|
89 lbs (48
kg)
|
|
Vibration
|
ISTA 1A in
carton (International Safe Transit Association)
|
|
Regulatory
compliance
|
|
Safety
|
CE, c-UL,
UL
|
|
EMI/EMC
|
CE, C-tick, FCC
Class A, ICES, VCCI
|
|
Environmental
|
Complies with
the appropriate requirements of RoHS, WEEE.
|
|
Warranty
|
3 years parts
and labor
|
|
NOTE
|
All nominal
levels are at ±10%.
|
|
|
| |
|
|
| |
|
|
