|
Video input — XTP CP 4i, XTP CP 4i
DMA
|
|
Number/signal
type
|
4 sets of
proprietary twisted pair AV signals
|
|
Connectors
|
4 female RJ-45
per board
|
|
NOTE
|
Input comes from an Extron XTP Series
twisted pair transmitter.
|
|
|
Control/remote — external
device (pass-through, unidirectional or
bidirectional)
|
|
Serial control
port input/output
|
1 set of
proprietary signals on a female RJ-45 jack
|
|
Serial control
port output/input
|
RS-232 (+5) via
(1) 3.5 mm, 5-pole captive screw connector (uses 3 poles)
(connector is shared with IR control port)
|
|
Baud
rates
|
Up to 115200
baud
|
|
Protocol
|
Data bits = 5 -
8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
|
|
Serial control
pin configuration
|
1 = Tx, 2 = Rx,
3 = GND
|
|
Ethernet
pass-through port
|
1 female RJ-45
connector
|
|
Ethernet data
rate
|
10/100Base-T,
half/full duplex with autodetect
|
|
IR control
port
|
(1) 3.5 mm,
captive screw connector, 5 pole (connector is shared with RS-232
control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to
40 kHz
|
|
IR control pin
configuration
|
3 = GND, 4 = IR
Tx, 5 = IR Rx
|
|
Video output — XTP CP 4o
|
|
Number/signal
type
|
4 sets of
proprietary twisted pair AV signals
|
|
Connectors
|
4 female RJ-45
per board
|
|
NOTE
|
Output connects to an Extron XTP Series
twisted pair receiver.
|
|
|
Control/remote — external
device (pass-through, unidirectional or
bidirectional)
|
|
Serial control
port input/output
|
1 set of
proprietary signals on a female RJ-45 jack
|
|
Serial control
port output/input
|
RS-232 (+5) via
(1) 3.5 mm, 5-pole captive screw connector (uses 3 poles)
(connector is shared with IR control port)
|
|
Baud
rates
|
Up to 115200
baud
|
|
Protocol
|
Data bits = 5 -
8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
|
|
Serial control
pin configuration
|
1 = Tx, 2 = Rx,
3 = GND
|
|
Ethernet
pass-through port
|
1 female RJ-45
connector
|
|
Ethernet data
rate
|
10/100Base-T,
half/full duplex with autodetect
|
|
IR control
port
|
(1) 3.5 mm,
captive screw connector, 5 pole (connector is shared with RS-232
control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to
40 kHz
|
|
IR control pin
configuration
|
3 = GND, 4 = IR
Tx, 5 = IR Rx
|
|
Video — XTP CP 4i VGA
|
|
Gain
|
Unity
|
|
Analog resolution
range
|
Up to
1920x1200* or 1080p (HDTV)
*reduced blanking
|
|
Bandwidth
|
300 MHz (-3
dB), fully loaded
0-10 MHz: no more than +0.1 dB to -0.1 dB
0-130 MHz: no more than +0.8 dB to -0.8 dB
|
|
Crosstalk
|
-88 dB @ 1 MHz,
-55 dB @ 10 MHz, -45 dB @ 30 MHz, -37 dB @ 100 MHz
|
|
Switching
speed
|
200 ms
(max.)
|
|
Video input — XTP CP 4i VGA
|
|
Number/signal
type
|
4 analog
VGA-QXGA RGBHV, RGBS, RGsB, RsGsBs, HDTV, component video, S-video,
composite video
|
|
Connectors
|
4 female
15-pin HD
|
|
Nominal
level
|
1 Vp-p for Y of
component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
|
|
Minimum/maximum
levels
|
Analog: 0.5 V
to 2.0 Vp-p with no offset
|
|
Impedance
|
75
ohms
|
|
Return loss
|
>30 dB @ 5
MHz
|
|
DC offset (max.
allowable)
|
1.5
V
|
|
Video processing — XTP CP 4i
VGA
|
|
Decoder
|
8 bit
digital
|
|
Digital
sampling
|
30 bit, 10 bits
per color; 162 MHz standard
|
|
Colors
|
1
billion
|
|
Sync — XTP CP 4i VGA
|
|
Input type
|
RGBHV, RGBS,
RGsB, RsGsBs
|
|
Input level
|
0.5 V to 5.0
Vp-p, 4.0 Vp-p normal
|
|
Input
impedance
|
510
ohms
|
|
Horizontal
frequency
|
30 kHz to 100
kHz
|
|
Vertical
frequency
|
24 Hz to 120
Hz
|
|
Max. propagation
delay
|
30
ns
|
|
Max. rise/fall
time
|
4
ns
|
|
Polarity
|
Positive or
negative
|
|
Video — XTP CP 4i DVI Pro, XTP CP 4o
DVI Pro
|
|
NOTE
|
*Appropriate DVI-D to HDMI cables or adapters are
required for HDMI signal input/output.
|
|
|
Gain
|
Unity
|
|
Resolution
range
|
Up to
1920x1200*, 2k, or 1080p @ 60 Hz
*Reduced blanking
|
|
Signal type
|
Single link DVI
digital video signals are supported.
|
|
Digital
video
|
RGB digital
video (DVI and HDMI standards) or Y, Cr, Cb digital component video
(HDMI), actively buffered (supports all single link DVI and HDMI
(if using an optional adapter) standards from 640x480 @ 60 Hz to
1920x1200 @ 60 Hz computer video) or 2k
|
|
NOTE
|
These XTP CP DVI Pro boards are compatible with
HDMI.
|
|
|
Digital
audio
|
Supports HDMI
audio (if using an HDMI to DVI adapter) transmitted through the RGB
and Y, Cr, Cb lines, actively buffered.
|
|
Consumer
Electronics Control (CEC)
|
Not
supported
|
|
EDID and
DDC
|
Supports
Extended Display Identification Data (EDID) and Display Data
Channel (DDC) data using DVI and HDMI standards. EDID and DDC
signals are actively buffered.
|
|
HDCP
|
Compliant with
High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI
standards
|
|
HPD
|
Supports hot
plug detection (HPD) of display as a pass-through
signal.
|
|
Maximum data
rate
|
6.75 Gbps (2.25
Gbps per color)
|
|
Maximum pixel
clock
|
165
MHz
|
|
Standards
|
DVI 1.0, HDMI,
HDCP 1.1
|
|
Switching
speed
|
200 ns,
max.
|
|
Video input — XTP CP 4i DVI
Pro
|
|
Number/signal
type
|
4 digital RGB
single link DVI-D (or HDMI*)
|
|
Connectors
|
4 female DVI-I
(digital only)
|
|
Equalization
|
Automatic
|
|
Input cable
length
|
>100' (30 m)
at 1920x1200, 2k, or 1080p @ 60 Hz
|
|
NOTE
|
The transmission distance varies depending on the
signal resolution and on the type of cable, graphics card, and
display used in the system.
|
|
|
Video output — XTP CP 4o DVI
Pro
|
|
Number/signal
type
|
4 digital RGB
single link DVI-D (or HDMI*)
|
|
Connectors
|
4 DVI-I
(digital only)
|
|
Re-clocking
|
Automatic
|
|
Peripheral device
power
|
5 VDC, 250 mA
per output
|
|
Video — XTP CP 4i HDMI, XTP CP 4i HDMI DMA,
XTP CP 4o HDMI
|
|
NOTE
|
*Appropriate HDMI to DVI-D cables or adapters
are required for DVI signal input/output.
|
|
|
Gain
|
Unity
|
|
Resolution
range
|
Up to
1920x1200*, 2k, or 1080p @ 60 Hz
*Reduced blanking
|
|
Signal type
|
Single-link
HDMI (or DVI-D*)
|
|
Digital
video
|
RGB digital
video (DVI and HDMI standards) or Y, Cr, Cb digital component video
(HDMI), actively buffered (supports all single-link DVI (if using
an optional adapter) and HDMI standards from 640x480 @ 60 Hz to
1920x1200 @ 60 Hz) or 2k
|
|
Consumer
Electronics Control (CEC)
|
Not
supported
|
|
EDID and
DDC
|
Supports
Extended Display Identification Data (EDID) and Display Data
Channel (DDC) data using DVI and HDMI standards. EDID and DDC
signals are actively buffered.
|
|
HDCP
|
Compliant with
High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI
standards
|
|
HPD
|
Supports hot
plug detection (HPD) of display as a pass-through
signal.
|
|
Maximum data
rate
|
6.75 Gbps (2.25
Gbps per color)
|
|
Maximum pixel
clock
|
165
MHz
|
|
Standards
|
DVI 1.0, HDMI,
HDCP 1.1
|
|
Switching
speed
|
200 ns,
max.
|
|
Video input — XTP CP 4i HDMI, XTP CP 4i HDMI
DMA
|
|
Number/signal
type
|
4 digital RGB
single-link HDMI (or DVI-D*)
|
|
Connectors
|
4 female HDMI
type A
|
|
Equalization
|
Automatic
|
|
Input cable
length
|
>100' (30 m)
at 1920x1200, 2k, or 1080p @ 60 Hz
|
|
NOTE
|
The transmission distance varies depending on the
signal resolution and on the type of cable, graphics card, and
display used in the system.
|
|
|
Video output — XTP CP 4o HDMI
|
|
Number/signal
type
|
4 digital RGB
single-link HDMI (or DVI-D*)
|
|
Connectors
|
4 female HDMI
type A
|
|
Re-clocking
|
Automatic
|
|
Peripheral device
power
|
5 VDC, 250 mA
per output
|
|
Audio input — XTP CP 4i DMA, XTP CP 4i HDMI
DMA
|
|
Supported formats — Pass
through / down mix
|
|
XTP/HDMI
connector
|
LPCM up to
7.1/24-bit/192kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital
EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital
2/0, DTS-HD Master Audio, DTS-HD, DTS ES Discrete 6.1, DTS ES
Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
|
|
Analog
connector
|
Analog stereo
audio
|
|
Audio — XTP CP 4i VGA, XTP CP 4o
SA
|
|
Gain
|
Unbalanced
output: -6 dB; balanced output 0 dB
|
|
Frequency
response
|
20 Hz to 20
kHz, ±0.05 dB
|
|
THD + Noise
|
0.03% @ 1 kHz
at nominal level
|
|
S/N
|
>90 dB at
maximum output (21 dBu, unweighted) (balanced)
|
|
Crosstalk
|
<-80 dB @ 1
kHz, fully loaded
|
|
Stereo channel
separation
|
>80 dB @ 1
kHz
|
|
CMRR
|
>75 dB @ 20
Hz to 20 kHz
|
|
Audio input — XTP CP 4i VGA
|
|
Number/signal
type
|
4 stereo,
balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm
captive screw connector, 5 pole
|
|
Supported
formats
|
Analog stereo
audio
|
|
Impedance
|
>10k ohms
unbalanced/balanced, DC coupled
|
|
Nominal
level
|
0 dBu (0.775
Vrms)
|
|
Maximum
level
|
+19.5 dBu,
(balanced or unbalanced) at 1% THD+N
|
|
Input gain
adjustment
|
-18 dB to +18
dB, adjustable per input; default = 0 dB
|
|
NOTE
|
0
dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2
dBu
|
|
|
Audio output — XTP CP 4o SA
|
|
Number/signal
type
|
4 stereo,
balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm
captive screw connector, 5 pole
|
|
Supported
formats
|
Analog stereo
audio
|
|
Impedance
|
50 ohms
unbalanced, 100 ohms balanced
|
|
Gain error
|
±0.1 dB
channel to channel
|
|
Maximum level
(Hi-Z)
|
>+21 dBu,
balanced or unbalanced at 0.1% THD+N
|
|
Maximum level (600
ohm)
|
>+15 dBm,
balanced or unbalanced at 0.1% THD+N
|
|
Volume control
range
|
-98 dB to 0 dB
(volume numbers 0 through 64) in a 35 dB increment from step 0 to
step 1, then in 1 dB increments from steps 1 to 64; default = 64
(0 dB)
|
|
NOTE
|
Attenuation = volume number minus 64. The default
is 0 dB = volume number 64.
|
|
|
Audio — XTP CP 4i DVI Pro, XTP CP 4o DVI
Pro, XTP CP 4i HDMI, XTP CP 4o HDMI
|
|
Gain
|
Unbalanced
output: -6 dB; balanced output 0 dB
|
|
Frequency
response
|
20 Hz to 20
kHz, ±0.05 dB
|
|
THD + Noise
|
0.01% @ 1 kHz
at nominal level
|
|
S/N
|
>105 dB at
maximum output (21 dBu, unweighted) (balanced)
|
|
Crosstalk
|
<-89 dB @ 1
kHz, fully loaded
|
|
Stereo channel
separation
|
>105 dB @ 1
kHz
|
|
CMRR
|
>83 dB @ 20
Hz to 20 kHz
|
|
Audio input — XTP CP 4i DVI Pro, XTP CP 4i
HDMI
|
|
Number/signal
type
|
4 stereo,
balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm
captive screw connector, 5 pole
|
|
Supported formats — Pass
through
|
|
HDMI/DVI Pro
connector
|
LPCM up to
7.1/24-bit/192kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital
EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital
2/0, DTS-HD Master Audio, DTS-HD, DTS ES Discrete 6.1, DTS ES
Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
|
|
Analog
connector
|
Analog stereo
audio
|
|
Impedance
|
>10k ohms
unbalanced/balanced, DC coupled
|
|
Nominal
level
|
+4 dBu (1.228
Vrms)
|
|
Maximum
level
|
+21 dBu,
(balanced or unbalanced) at 0.01% THD+N
+19.5 dBu, (balanced or unbalanced) at 1% THD+N
|
|
Input gain
adjustment
|
-18 dB to +18
dB, adjustable per input; default = 0 dB
|
|
|
|
Audio output — XTP CP 4o DVI Pro, XTP CP 4o
HDMI
|
|
Number/signal
type
|
4 stereo,
balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm
captive screw connector, 5 pole
|
|
Supported formats — Pass
through
|
|
HDMI/DVI Pro
connector
|
LPCM up to
7.1/24-bit/192kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital
EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital
2/0, DTS-HD Master Audio, DTS-HD, DTS ES Discrete 6.1, DTS ES
Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
|
|
Analog
connector
|
Analog stereo
audio
|
|
Impedance
|
50 ohms
unbalanced, 100 ohms balanced
|
|
Gain error
|
±0.1 dB
channel to channel
|
|
Maximum level
(Hi-Z)
|
>+21 dBu,
balanced or unbalanced at 1% THD+N
|
|
Maximum level (600
ohm)
|
>+20 dBm,
balanced or unbalanced at 1% THD+N
|
|
Volume control
range
|
-75.8 dB to 0
dB (volume numbers 0 through 64) in a 35 dB increment from step 0
to step 1, then in 1 dB increments from steps 1 to 64; default = 64
(0 dB)
|
|
NOTE
|
Attenuation = volume number minus 64. The default
is 0 dB = volume number 64.
|
|
|
Control/remote — switcher host
ports
|
|
NOTE
|
The front panel USB port and rear panel RS-232
port are independent of each other and can be used at the same
time.
|
|
|
Serial host control
port
|
1 bidirectional
RS-232 or RS-422, rear panel female 9-pin D
connector
|
|
Baud rate and
protocol
|
9600 (default)
to 115200 baud, 8 data bits, 1 stop bit, no parity, no flow
control
|
|
Serial control pin
configurations
|
|
RS-232
|
2 = Tx, 3 = Rx,
5 = GND
|
|
RS-422
|
2 = Tx-, 3 =
Rx-, 5 = GND, 7 = Rx+, 8 = Tx+
|
|
USB control
port
|
1 front panel
female mini USB B
|
|
USB
standards
|
USB 2.0, low
speed
|
|
Ethernet control
port
|
1 female
RJ-45
|
|
Ethernet data rate (for network
communication)
|
10/100Base-T,
half/full duplex with autodetect
|
|
Ethernet
protocol
|
ARP, ICMP
(ping), IP, TCP, DHCP, HTTP, SMTP, Telnet
|
|
Ethernet default
settings
|
Link speed and
duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Default gateway = 0.0.0.0
DHCP = off
|
|
Web server
|
Up to 200
simultaneous sessions
7.0 MB nonvolatile user memory
|
|
Program
control
|
Extron XTP
System Configuration Software for Windows®
Extron Simple Instruction Set (SIS™)
Microsoft® Internet Explorer® ver. 6 or higher,
Telnet
|
|
General
|
|
Power
|
Internal
Input: 100-240 VAC, 50-60 Hz
|
|
XTP CrossPoint
1600
|
Redundant power
supply is optional.
|
|
XTP CrossPoint
3200
|
Redundant power
supply is standard.
|
|
Power
consumption
|
|
XTP CrossPoint
1600
|
50 to 810
watts, depending on configuration
|
|
XTP CrossPoint
3200
|
100 to 1200
watts, depending on configuration
|
|
Individual I/O
boards
|
TBD
|
|
Remote power
capability
|
|
XTP CrossPoint
1600
|
Supports up to
28 endpoints
|
|
XTP CrossPoint
3200
|
Supports up to
24 endpoints.
|
|
Temperature/humidity
|
Storage: -40 to
+158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%,
noncondensing
|
|
Cooling
|
Fan, right to
left (as viewed from front panel)
|
|
Mounting
|
|
Rack
mount
|
Yes
|
|
Enclosure
type
|
Metal
|
|
Enclosure dimensions (Depth
excludes connectors. Width excludes rack ears.)
|
|
XTP CrossPoint
1600
|
8.75" H x 17.0"
W x 17.5" D (5U high, full rack wide)
(22.2 cm H x 43.2 cm W x 44.5 cm D)
|
|
XTP CrossPoint
3200
|
17.5" H x 17.0"
W x 17.5" D (10U high, full rack wide)
(44.5 cm H x 43.2 cm W x 44.5 cm D)
|
|
Product weight with boards
installed
|
|
XTP CrossPoint
1600
|
39.0 lbs (17.7
kg)
|
|
XTP CrossPoint
3200
|
59.0 lbs (26.8
kg)
|
|
Shipping weight with boards
installed
|
|
XTP CrossPoint
1600
|
48 lbs (22
kg)
|
|
XTP CrossPoint
3200
|
71 lbs (33
kg)
|
|
Shipping weight of individual
boards, if purchased separately
|
2 lbs (1
kg)
|
|
DIM weight
|
|
XTP CrossPoint
1600
|
|
International
|
53 lbs (24
kg)
|
|
XTP CrossPoint
3200
|
|
USA/Canada
|
76 lbs (35
kg)
|
|
International
|
89 lbs (48
kg)
|
|
Vibration
|
ISTA 1A in
carton (International Safe Transit Association)
|
|
Regulatory
compliance
|
|
Safety
|
CE, c-UL,
UL
|
|
EMI/EMC
|
CE, C-tick, FCC
Class A, ICES, VCCI
|
|
Environmental
|
Complies with
the appropriate requirements of RoHS, WEEE.
|
|
Warranty
|
3 years parts
and labor
|
|
NOTE
|
All nominal
levels are at ±10
|
|
