| The Extron MAV SVA Series matrix switchers are
designed to route S-video and balanced/unbalanced stereo audio signals. They are
ideal for use in a wide range of matrix switching applications, including
museums, sports bars, videoconferencing rooms, and home theaters. |
•
Inputs: Video on female 4-pin mini DIN connectors;
audio on captive screw connectors
• Outputs: Video on female 4-pin mini DIN connectors; audio on captive screw
connectors
• 150 MHz (-3 dB) video bandwidth, fully loaded — Ensures switching and
distribution of video signals without degradation. MAV Series matrix switchers
provide a minimum 150 MHz (-3 dB) of video bandwidth at full performance
capability when one input drives all outputs.
• Video genlock — Allows for vertical interval switching and enables smooth,
seamless transitions when switching between synchronous video sources.
• Compatible with NTSC 3.58, NTSC 4.42, PAL, and SECAM video — Provides for
worldwide compatibility.
• Switches both balanced and unbalanced stereo audio — Accepts both signals on
captive screw connectors.
• Audio input gain and attenuation — Allows users to set the level of gain or
attenuation for each audio input channel, eliminating noticeable differences
when switching between sources.
• Audio breakaway — Provides the capability to break an audio signal away from
its corresponding video signal, allowing the audio and video signals from one
source to be switched to different destinations.
• QS-FPC™ - QuickSwitch Front Panel Controller — Provides a discrete button for
each input and output, allowing for simple, intuitive operation.
• View I/O mode — Easily view which inputs and outputs are actively connected.
• Global presets — Frequently used I/O configurations may be saved and recalled
either from the QuickSwitch Front Panel Controller or RS-232 serial control.
This time-saving feature allows you to set up I/O configurations and store them
in memory for future use.
• RS-232 control port — Using serial commands, the MAV Series can be controlled
and configured via the included Windows-based control software, or integrated
into a control system. Extron products use the SIS™ - Simple Instruction Set
command protocol, a set of basic ASCII code commands that allow for quick and
easy programming. The RS-232 port also makes it easy to install firmware
updates.
• Optional IR 501 remote control
• Control software — Provides a graphical, drag-and-drop interface for I/O
configuration and other customization functions via RS-232 remote control. This
software also offers an emulation mode for configuration of an offsite matrix
switcher; the I/O configuration may be saved for future downloading to the
matrix switcher.
• Optional remote control — Optional X/Y control panels, bus control panels, and
keypads provide the flexibility to control a MAV Series matrix switcher from a
remote location.
• Front panel security lockout — Prevents unauthorized use when the matrix
switcher is installed in an unsecured environment where easy access is not
desirable. In lockout mode, a special button combination is required to operate
the front panel.
• 1U, rack-mountable metal enclosure
• Highly reliable, energy-efficient internal universal power supply — The
100-240 VAC, 50/60 Hz, international power supply provides worldwide power
compatibility with high demonstrated reliability. |
|
Video — composite video and S-video models |
|
Routing |
|
MAV 44 Series |
4
x 4 matrix |
|
MAV 48 Series |
4
x 8 matrix |
|
MAV 84 Series |
8
x 4 matrix |
|
MAV 88 Series |
8
x 8 matrix |
|
Gain |
Unity |
|
Bandwidth |
150 MHz (-3 dB), fully loaded |
|
Differential phase error |
<0.1° at 3.58 MHz and 4.43 MHz |
|
Differential gain error |
<0.1% at 3.58 MHz and 4.43 MHz |
|
Crosstalk |
<-50 dB @ 5 MHz |
|
Switching speed |
20 ms (max.) |
|
Video input — composite video and S-video
models |
|
Number/signal type |
|
MAV 44 AV, MAV 44 AV RCA, MAV 48
AV, MAV 48 AV RCA |
4
composite video |
|
MAV 44 SVA, MAV 44 SVA RCA, MAV
48 SVA, MAV 48 SVA RCA |
4
S-video |
|
MAV 84 AV, MAV 84 AV RCA, MAV 88 AV,
MAV 88 AV RCA, MAV 88 V |
8
composite video |
|
MAV 84 SVA, MAV 84 SVA RCA, MAV
88 SVA, MAV 88 SVA RCA |
8
S-video |
|
Connectors |
|
MAV 44/48 composite video
models |
4
female BNC |
|
MAV 44/48 S-video models |
4
female 4-pin mini DIN |
|
MAV 44/48 composite video
models |
8
female BNC |
|
MAV 84/88 S-video models |
8
female 4-pin mini DIN |
|
Nominal level |
1
Vp-p for Y of S-video, and for composite video
0.3 Vp-p for C of S-video |
|
Minimum/maximum levels |
Analog: 0.4 V to 2.0 Vp-p with no offset at unity gain |
|
Impedance |
75 ohms |
|
Return loss |
|
Composite video |
<-38 dB @ 0 to 10 MHz |
|
S-video |
<-25 dB @ 0 to 10 MHz |
|
DC offset (max. allowable) |
5
V |
|
External sync (genlock) |
0.2 V to 0.4 Vp-p |
|
Input coupling |
AC coupling only |
|
Video output — composite video and S-video
models |
|
Number/signal type |
|
MAV 44 AV, MAV 44 AV RCA, MAV 84
AV, MAV 84 AV RCA |
4
composite video |
|
MAV 44 SVA, MAV 44 SVA RCA, MAV
84 SVA, MAV 84 SVA RCA |
4
S-video |
|
MAV 88 AV, MAV 88 AV RCA, MAV 88 V,
MAV 48 AV, MAV 48 AV RCA |
8
composite video |
|
MAV 88 SVA, MAV 88 SVA RCA, MAV
48 SVA, MAV 48 SVA RCA |
8
S-video |
|
Connectors |
|
MAV 44/84 composite video
models |
4
female BNC |
|
MAV 44/84 S-video models |
4
female 4-pin mini DIN |
|
MAV 48/88 composite video
models |
8
female BNC |
|
MAV 48/88 S-video models |
8
female 4-pin mini DIN |
|
Nominal level |
1
Vp-p for Y of S-video, and for composite video
0.3 Vp-p for C of S-video |
|
Minimum/maximum levels |
0.4 V to 2.0 Vp-p (follows input) |
|
Impedance |
75 ohms |
|
Return loss |
|
Composite video |
<-40 dB @ 5 MHz |
|
S-video |
<-25 dB @ 5 MHz |
|
DC offset |
15 mV typical (per output enabled with 75 ohm termination) with input at
0 offset |
|
Switching type |
Vertical interval |
|
Sync — composite video and S-video models |
|
Genlock connectors |
2
female BNC |
|
Standards |
NTSC 3.58, NTSC 4.43, PAL, SECAM |
|
Audio — audio models |
|
Routing |
|
MAV 44 Series |
4
x 4 stereo matrix |
|
MAV 48 Series |
4
x 8 stereo matrix |
|
MAV 84 Series |
8
x 4 stereo matrix |
|
MAV 88 Series |
8
x 8 stereo matrix |
|
Gain |
Adjustable; the default is unity. Unity gain occurs for all RCA
connector models. In all other models with captive screw connectors,
unity gain occurs when the switcher is configured for balanced output. |
|
Frequency response |
20 Hz to 20 kHz, ±0.5 dB |
|
THD + Noise |
1% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
|
S/N |
90 dB at maximum output (unweighted) |
|
Crosstalk |
<-65 dB @ 20 kHz, <-80 dB @ 1 kHz or below 60 Hz, fully loaded |
|
Stereo channel separation |
>80 dB @ 20 Hz to 20 kHz |
|
CMRR |
>75 dB @ 20 Hz to 20 kHz |
|
Audio input — audio models |
|
Number/signal type |
|
MAV 44 AV, MAV 44 SVA, MAV 48
AV, MAV 48 SVA |
4
stereo, balanced/unbalanced |
|
MAV 44 AV RCA, MAV 44 SVA RCA, MAV 48 AV RCA, MAV 48 SVA RCA |
4
stereo, unbalanced |
|
MAV 84 AV, MAV 84 SVA, MAV 88
AV, MAV 88 SVA |
8
stereo, balanced/unbalanced |
| MAV
84 AV RCA, MAV 84 SVA RCA, MAV 88 AV RCA, MAV 88 SVA RCA |
8
stereo, unbalanced |
|
Connectors |
|
MAV 44 AV, MAV 44 SVA, MAV 48
AV, MAV 48 SVA |
(4) 3.5 mm captive screw connectors, 5 pole |
| MAV
44 AV RCA, MAV 44 SVA RCA, MAV 48 AV RCA, MAV 48 SVA RCA |
4
pairs of female RCA connectors |
|
MAV 84 AV, MAV 84 SVA, MAV 88
AV, MAV 88 SVA |
(8) 3.5 mm captive screw connectors, 5 pole |
|
MAV 84 AV RCA, MAV 84 SVA RCA, MAV 88 AV RCA, MAV 88 SVA RCA |
8
pairs of female RCA connectors |
|
Impedance |
>18k ohms unbalanced, 24k ohms balanced, DC coupled |
|
Nominal level |
Configurable: +4 dBu (1.23 V, professional level) or -10 dBV (316 mV,
consumer level) |
|
Maximum level |
>+20 dBu (captive screw models) at 1% THD+N
>+14 dBu (RCA models) at 1% THD+N |
|
Input gain adjustment |
–18 dB to +10 dB, adjustable per input; default = 0 dB. |
| NOTE |
Input gain is referenced to the internal bus signal level. It
can be verified by measuring the unbalanced output level when
the output level is set to "Consumer". |
|
| NOTE |
0
dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
Audio output — audio models |
|
Number/signal type |
|
MAV 44 AV, MAV 44 SVA, MAV 48
AV, MAV 48 SVA |
4
stereo, balanced/unbalanced |
| MAV
44 AV RCA, MAV 44 SVA RCA, MAV 48 AV RCA, MAV 48 SVA RCA |
4
stereo, unbalanced |
|
MAV 88 AV, MAV 88 SVA, MAV 48
AV, MAV 48 SVA |
8
stereo, balanced/unbalanced |
| MAV
88 AV RCA, MAV 88 SVA RCA, MAV 48 AV RCA, MAV 48 SVA RCA |
8
stereo, unbalanced |
|
Connectors |
|
MAV 44 AV, MAV 44 SVA, MAV 84
AV, MAV 84 SVA |
(2) 3.5 mm captive screw connectors, 10 pole |
| MAV
44 AV RCA, MAV 44 SVA RCA, MAV 48 AV RCA, MAV 48 SVA RCA |
4
pairs of RCA female |
|
MAV 88 AV, MAV 88 SVA, MAV 48
AV, MAV 48 SVA |
(4) 3.5 mm captive screw connectors, 10 pole |
|
MAV 88 AV RCA, MAV 88 SVA RCA, MAV 48 AV RCA, MAV 48 SVA RCA |
8
pairs of female RCA |
|
Impedance |
50 ohms unbalanced, 100 ohms balanced |
|
Gain error |
<±0.1 dB channel to channel |
|
Nominal level |
Configurable: +4 dBu (1.23 V, professional level) or -10 dBV (316 mV,
consumer level) |
|
Maximum level (Hi-Z) |
>+20 dBu, balanced; >+18 dBu, unbalanced at 1% THD+N at default settings |
|
Maximum level (600 ohm) |
>+19 dBm, balanced; >+13 dBm, unbalanced at 1%THD+N at default settings |
|
Control/remote — switcher |
|
Serial control port |
RS-232, female 9-pin D connector |
|
Baud rate and protocol |
9600 baud, 8 data bits, 1 stop bit, no parity |
|
Serial control pin configuration |
2
= TX, 3 = RX, 5 = GND, 9 = hardwired IR |
|
IR controller module |
IR 501 remote control (optional) |
|
Program control |
Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS™) |
|
General |
|
Power |
100 VAC to 240 VAC, 50-60 Hz, 15 watts, internal |
|
Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
|
Mounting |
|
Rack mount |
Yes, with included brackets |
|
Furniture mount |
Yes, with an optional under-desk mounting kit |
|
Cooling |
Convection, no vents |
|
Enclosure type |
Metal |
|
Enclosure dimensions |
1.75" H x 17.4" W x 8.5" D (1U high, full rack wide)
(4.4 cm H x 44.2 cm W x 21.6 cm D)
(Depth excludes connectors. Width excludes rack ears.) |
|
Product weight |
7.0 lbs (3.2 kg) |
|
Shipping weight |
10 lbs (5 kg) |
|
Vibration |
ISTA 1A in carton (International Safe Transit Association) |
|
&nbs; Regulatory compliance |
|
Safety |
CE, c-UL, UL |
|
EMI/EMC |
CE, C-tick, FCC Class A, ICES, VCCI |
|
Warranty |
3
years parts and labor |
|
| |
|
|
