|
Video input — XTP CP 4i, XTP
CP 4i DMA
|
|
Number/signal type
|
4 sets of proprietary twisted
pair AV signals
|
|
Connectors
|
4 female RJ-45 per board
|
|
NOTE
|
Input comes from an
Extron XTP Series twisted pair transmitter.
|
|
|
Control/remote — external
device (pass-through, unidirectional or bidirectional)
|
|
Serial control port
input/output
|
1 set of proprietary signals on
a female RJ-45 jack
|
|
Serial control port
output/input
|
RS-232 (+5) via (1) 3.5 mm,
5-pole captive screw connector (uses 3 poles) (connector is shared with IR
control port)
|
|
Baud rates
|
Up to 115200 baud
|
|
Protocol
|
Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
|
|
Serial control pin
configuration
|
1 = Tx, 2 = Rx, 3 = GND
|
|
Ethernet pass-through
port
|
1 female RJ-45 connector
|
|
Ethernet data rate
|
10/100Base-T, half/full duplex
with autodetect
|
|
IR control port
|
(1) 3.5 mm, captive screw
connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 40 kHz
|
|
IR control pin
configuration
|
3 = GND, 4 = IR Tx, 5 = IR Rx
|
|
Video output — XTP CP 4o
|
|
Number/signal type
|
4 sets of proprietary twisted
pair AV signals
|
|
Connectors
|
4 female RJ-45 per board
|
|
NOTE
|
Output connects to an
Extron XTP Series twisted pair receiver.
|
|
|
Control/remote — external
device (pass-through, unidirectional or bidirectional)
|
|
Serial control port
input/output
|
1 set of proprietary signals on
a female RJ-45 jack
|
|
Serial control port
output/input
|
RS-232 (+5) via (1) 3.5 mm,
5-pole captive screw connector (uses 3 poles) (connector is shared with IR
control port)
|
|
Baud rates
|
Up to 115200 baud
|
|
Protocol
|
Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
|
|
Serial control pin
configuration
|
1 = Tx, 2 = Rx, 3 = GND
|
|
Ethernet pass-through
port
|
1 female RJ-45 connector
|
|
Ethernet data rate
|
10/100Base-T, half/full duplex
with autodetect
|
|
IR control port
|
(1) 3.5 mm, captive screw
connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 40 kHz
|
|
IR control pin
configuration
|
3 = GND, 4 = IR Tx, 5 = IR Rx
|
|
Video — XTP CP 4i VGA
|
|
Gain
|
Unity
|
|
Analog resolution range
|
Up to 1920x1200* or 1080p
(HDTV)
*reduced blanking
|
|
Bandwidth
|
300 MHz (-3 dB), fully loaded
0-10 MHz: no more than +0.1 dB to -0.1 dB
0-130 MHz: no more than +0.8 dB to -0.8 dB
|
|
Crosstalk
|
-88 dB @ 1 MHz, -55 dB @ 10
MHz, -45 dB @ 30 MHz, -37 dB @ 100 MHz
|
|
Switching speed
|
200 ms (max.)
|
|
Video input — XTP CP 4i VGA
|
|
Number/signal type
|
4 analog VGA-QXGA RGBHV, RGBS,
RGsB, RsGsBs, HDTV, component video, S-video, composite video
|
|
Connectors
|
4 female 15-pin HD
|
|
Nominal level
|
1 Vp-p for Y of component video
and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
|
|
Minimum/maximum levels
|
Analog: 0.5 V to 2.0 Vp-p with
no offset
|
|
Impedance
|
75 ohms
|
|
Return loss
|
>30 dB @ 5 MHz
|
|
DC offset (max. allowable)
|
1.5 V
|
|
Video processing — XTP CP 4i
VGA
|
|
Decoder
|
8 bit digital
|
|
Digital sampling
|
30 bit, 10 bits per color; 162
MHz standard
|
|
Colors
|
1 billion
|
|
Sync — XTP CP 4i VGA
|
|
Input type
|
RGBHV, RGBS, RGsB, RsGsBs
|
|
Input level
|
0.5 V to 5.0 Vp-p, 4.0 Vp-p
normal
|
|
Input impedance
|
510 ohms
|
|
Horizontal frequency
|
30 kHz to 100 kHz
|
|
Vertical frequency
|
24 Hz to 120 Hz
|
|
Max. propagation delay
|
30 ns
|
|
Max. rise/fall time
|
4 ns
|
|
Polarity
|
Positive or negative
|
|
Video — XTP CP 4i DVI Pro,
XTP CP 4o DVI Pro
|
|
NOTE
|
*Appropriate DVI-D to HDMI
cables or adapters are required for HDMI signal input/output.
|
|
|
Gain
|
Unity
|
|
Resolution range
|
Up to 1920x1200*, 2k, or 1080p
@ 60 Hz
*Reduced blanking
|
|
Signal type
|
Single link DVI digital video
signals are supported.
|
|
Digital video
|
RGB digital video (DVI and HDMI
standards) or Y, Cr, Cb digital component video (HDMI), actively buffered
(supports all single link DVI and HDMI (if using an optional adapter) standards
from 640x480 @ 60 Hz to 1920x1200 @ 60 Hz computer video) or 2k
|
|
NOTE
|
These XTP CP DVI Pro boards
are compatible with HDMI.
|
|
|
Digital audio
|
Supports HDMI audio (if using
an HDMI to DVI adapter) transmitted through the RGB and Y, Cr, Cb lines,
actively buffered.
|
|
Consumer Electronics
Control (CEC)
|
Not supported
|
|
EDID and DDC
|
Supports Extended Display
Identification Data (EDID) and Display Data Channel (DDC) data using DVI and
HDMI standards. EDID and DDC signals are actively buffered.
|
|
HDCP
|
Compliant with High-bandwidth
Digital Content Protection (HDCP) using DVI and HDMI standards
|
|
HPD
|
Supports hot plug detection
(HPD) of display as a pass-through signal.
|
|
Maximum data rate
|
6.75 Gbps (2.25 Gbps per color)
|
|
Maximum pixel clock
|
165 MHz
|
|
Standards
|
DVI 1.0, HDMI, HDCP 1.1
|
|
Switching speed
|
200 ns, max.
|
|
Video input — XTP CP 4i DVI
Pro
|
|
Number/signal type
|
4 digital RGB single link DVI-D
(or HDMI*)
|
|
Connectors
|
4 female DVI-I (digital only)
|
|
Equalization
|
Automatic
|
|
Input cable length
|
>100' (30 m) at 1920x1200,
2k, or 1080p @ 60 Hz
|
|
NOTE
|
The transmission distance
varies depending on the signal resolution and on the type of cable, graphics
card, and display used in the system.
|
|
|
Video output — XTP CP 4o DVI
Pro
|
|
Number/signal type
|
4 digital RGB single link DVI-D
(or HDMI*)
|
|
Connectors
|
4 DVI-I (digital only)
|
|
Re-clocking
|
Automatic
|
|
Peripheral device power
|
5 VDC, 250 mA per output
|
|
Video — XTP CP 4i HDMI, XTP
CP 4i HDMI DMA, XTP CP 4o HDMI
|
|
NOTE
|
*Appropriate HDMI to DVI-D
cables or adapters are required for DVI signal input/output.
|
|
|
Gain
|
Unity
|
|
Resolution range
|
Up to 1920x1200*, 2k, or 1080p
@ 60 Hz
*Reduced blanking
|
|
Signal type
|
Single-link HDMI (or DVI-D*)
|
|
Digital video
|
RGB digital video (DVI and HDMI
standards) or Y, Cr, Cb digital component video (HDMI), actively buffered
(supports all single-link DVI (if using an optional adapter) and HDMI standards
from 640x480 @ 60 Hz to 1920x1200 @ 60 Hz) or 2k
|
|
Consumer Electronics
Control (CEC)
|
Not supported
|
|
EDID and DDC
|
Supports Extended Display
Identification Data (EDID) and Display Data Channel (DDC) data using DVI and
HDMI standards. EDID and DDC signals are actively buffered.
|
|
HDCP
|
Compliant with High-bandwidth
Digital Content Protection (HDCP) using DVI and HDMI standards
|
|
HPD
|
Supports hot plug detection
(HPD) of display as a pass-through signal.
|
|
Maximum data rate
|
6.75 Gbps (2.25 Gbps per color)
|
|
Maximum pixel clock
|
165 MHz
|
|
Standards
|
DVI 1.0, HDMI, HDCP 1.1
|
|
Switching speed
|
200 ns, max.
|
|
Video input — XTP CP 4i
HDMI, XTP CP 4i HDMI DMA
|
|
Number/signal type
|
4 digital RGB single-link HDMI
(or DVI-D*)
|
|
Connectors
|
4 female HDMI type A
|
|
Equalization
|
Automatic
|
|
Input cable length
|
>100' (30 m) at 1920x1200, 2k,
or 1080p @ 60 Hz
|
|
NOTE
|
The transmission distance
varies depending on the signal resolution and on the type of cable, graphics
card, and display used in the system.
|
|
|
Video output — XTP CP 4o
HDMI
|
|
Number/signal type
|
4 digital RGB single-link HDMI
(or DVI-D*)
|
|
Connectors
|
4 female HDMI type A
|
|
Re-clocking
|
Automatic
|
|
Peripheral device power
|
5 VDC, 250 mA per output
|
|
Audio input — XTP CP 4i DMA,
XTP CP 4i HDMI DMA
|
|
Supported formats — Pass
through / down mix
|
|
XTP/HDMI connector
|
LPCM up to 7.1/24-bit/192kHz,
Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby
Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS ES
Discrete 6.1, DTS ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
|
|
Analog connector
|
Analog stereo audio
|
|
Audio — XTP CP 4i VGA, XTP
CP 4o SA
|
|
Gain
|
Unbalanced output: -6 dB;
balanced output 0 dB
|
|
Frequency response
|
20 Hz to 20 kHz, ±0.05 dB
|
|
THD + Noise
|
0.03% @ 1 kHz at nominal level
|
|
S/N
|
>90 dB at maximum output (21
dBu, unweighted) (balanced)
|
|
Crosstalk
|
<-80 dB @ 1 kHz, fully loaded
|
|
Stereo channel separation
|
>80 dB @ 1 kHz
|
|
CMRR
|
>75 dB @ 20 Hz to 20 kHz
|
|
Audio input — XTP CP 4i VGA
|
|
Number/signal type
|
4 stereo, balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm captive screw
connector, 5 pole
|
|
Supported formats
|
Analog stereo audio
|
|
Impedance
|
>10k ohms unbalanced/balanced,
DC coupled
|
|
Nominal level
|
0 dBu (0.775 Vrms)
|
|
Maximum level
|
+19.5 dBu, (balanced or
unbalanced) at 1% THD+N
|
|
Input gain adjustment
|
-18 dB to +18 dB, adjustable
per input; default = 0 dB
|
|
NOTE
|
0 dBu = 0.775 Vrms, 0 dBV =
1 Vrms, 0 dBV ≈ 2 dBu
|
|
|
Audio output — XTP CP 4o SA
|
|
Number/signal type
|
4 stereo, balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm captive screw
connector, 5 pole
|
|
Supported formats
|
Analog stereo audio
|
|
Impedance
|
50 ohms unbalanced, 100 ohms
balanced
|
|
Gain error
|
±0.1 dB channel to channel
|
|
Maximum level (Hi-Z)
|
>+21 dBu, balanced or
unbalanced at 0.1% THD+N
|
|
Maximum level (600 ohm)
|
>+15 dBm, balanced or
unbalanced at 0.1% THD+N
|
|
Volume control range
|
-98 dB to 0 dB (volume numbers
0 through 64) in a 35 dB increment from step 0 to step 1, then in 1 dB
increments from steps 1 to 64; default = 64 (0 dB)
|
|
NOTE
|
Attenuation = volume number
minus 64. The default is 0 dB = volume number 64.
|
|
|
Audio — XTP CP 4i DVI Pro,
XTP CP 4o DVI Pro, XTP CP 4i HDMI, XTP CP 4o HDMI
|
|
Gain
|
Unbalanced output: -6 dB;
balanced output 0 dB
|
|
Frequency response
|
20 Hz to 20 kHz, ±0.05 dB
|
|
THD + Noise
|
0.01% @ 1 kHz at nominal level
|
|
S/N
|
>105 dB at maximum output (21
dBu, unweighted) (balanced)
|
|
Crosstalk
|
<-89 dB @ 1 kHz, fully loaded
|
|
Stereo channel separation
|
>105 dB @ 1 kHz
|
|
CMRR
|
>83 dB @ 20 Hz to 20 kHz
|
|
Audio input — XTP CP 4i DVI
Pro, XTP CP 4i HDMI
|
|
Number/signal type
|
4 stereo, balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm captive screw
connector, 5 pole
|
|
Supported formats — Pass
through
|
|
HDMI/DVI Pro connector
|
LPCM up to 7.1/24-bit/192kHz,
Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby
Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS ES
Discrete 6.1, DTS ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
|
|
Analog connector
|
Analog stereo audio
|
|
Impedance
|
>10k ohms unbalanced/balanced,
DC coupled
|
|
Nominal level
|
+4 dBu (1.228 Vrms)
|
|
Maximum level
|
+21 dBu, (balanced or
unbalanced) at 0.01% THD+N
+19.5 dBu, (balanced or unbalanced) at 1% THD+N
|
|
Input gain adjustment
|
-18 dB to +18 dB, adjustable
per input; default = 0 dB
|
|
Audio output — XTP CP 4o DVI
Pro, XTP CP 4o HDMI
|
|
Number/signal type
|
4 stereo, balanced/unbalanced
|
|
Connectors
|
(4) 3.5 mm captive screw
connector, 5 pole
|
|
Supported formats — Pass
through
|
|
HDMI/DVI Pro connector
|
LPCM up to 7.1/24-bit/192kHz,
Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby
Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS ES
Discrete 6.1, DTS ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel
|
|
Analog connector
|
Analog stereo audio
|
|
Impedance
|
50 ohms unbalanced, 100 ohms
balanced
|
|
Gain error
|
±0.1 dB channel to channel
|
|
Maximum level (Hi-Z)
|
>+21 dBu, balanced or
unbalanced at 1% THD+N
|
|
Maximum level (600 ohm)
|
>+20 dBm, balanced or
unbalanced at 1% THD+N
|
|
Volume control range
|
-75.8 dB to 0 dB (volume
numbers 0 through 64) in a 35 dB increment from step 0 to step 1, then in 1 dB
increments from steps 1 to 64; default = 64 (0 dB)
|
|
NOTE
|
Attenuation = volume number
minus 64. The default is 0 dB = volume number 64.
|
|
|
Control/remote — switcher
host ports
|
|
NOTE
|
The front panel USB port and
rear panel RS-232 port are independent of each other and can be used at the same
time.
|
|
|
Serial host control port
|
1 bidirectional RS-232 or
RS-422, rear panel female 9-pin D connector
|
|
Baud rate and protocol
|
9600 (default) to 115200 baud,
8 data bits, 1 stop bit, no parity, no flow control
|
|
Serial control pin
configurations
|
|
RS-232
|
2 = Tx, 3 = Rx, 5 = GND
|
|
RS-422
|
2 = Tx-, 3 = Rx-, 5 = GND, 7 =
Rx+, 8 = Tx+
|
|
USB control port
|
1 front panel female mini USB B
|
|
USB standards
|
USB 2.0, low speed
|
|
Ethernet control port
|
1 female RJ-45
|
|
Ethernet data rate (for
network communication)
|
10/100Base-T, half/full duplex
with autodetect
|
|
Ethernet protocol
|
ARP, ICMP (ping), IP, TCP,
DHCP, HTTP, SMTP, Telnet
|
|
Ethernet default settings
|
Link speed and duplex level =
autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Default gateway = 0.0.0.0
DHCP = off
|
|
Web server
|
Up to 200 simultaneous sessions
7.0 MB nonvolatile user memory
|
|
Program control
|
Extron XTP System Configuration
Software for Windows®
Extron Simple Instruction Set (SIS™)
Microsoft® Internet Explorer® ver. 6 or higher, Telnet
|
|
General
|
|
Power
|
Internal
Input: 100-240 VAC, 50-60 Hz
|
|
XTP CrossPoint 1600
|
Redundant power supply is
optional.
|
|
XTP CrossPoint 3200
|
Redundant power supply is
standard.
|
|
Power consumption
|
|
XTP CrossPoint 1600
|
50 to 810 watts, depending on
configuration
|
|
XTP CrossPoint 3200
|
100 to 1200 watts, depending on
configuration
|
|
Individual I/O boards
|
TBD
|
|
Remote power capability
|
|
XTP CrossPoint 1600
|
Supports up to 28 endpoints
|
|
XTP CrossPoint 3200
|
Supports up to 24 endpoints.
|
|
Temperature/humidity
|
Storage: -40 to +158 °F (-40 to
+70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
|
|
Cooling
|
Fan, right to left (as viewed
from front panel)
|
|
Mounting
|
|
Rack mount
|
Yes
|
|
Enclosure type
|
Metal
|
|
Enclosure dimensions
(Depth excludes connectors. Width excludes rack ears.)
|
|
XTP CrossPoint 1600
|
8.75" H x 17.0" W x 17.5" D (5U
high, full rack wide)
(22.2 cm H x 43.2 cm W x 44.5 cm D)
|
|
XTP CrossPoint 3200
|
17.5" H x 17.0" W x 17.5" D
(10U high, full rack wide)
(44.5 cm H x 43.2 cm W x 44.5 cm D)
|
|
Product weight with
boards installed
|
|
XTP CrossPoint 1600
|
39.0 lbs (17.7 kg)
|
|
XTP CrossPoint 3200
|
59.0 lbs (26.8 kg)
|
|
Shipping weight with
boards installed
|
|
XTP CrossPoint 1600
|
48 lbs (22 kg)
|
|
XTP CrossPoint 3200
|
71 lbs (33 kg)
|
|
Shipping weight of
individual boards, if purchased separately
|
2 lbs (1 kg)
|
|
DIM weight
|
|
XTP CrossPoint 1600
|
|
International
|
53 lbs (24 kg)
|
|
XTP CrossPoint 3200
|
|
USA/Canada
|
76 lbs (35 kg)
|
|
International
|
89 lbs (48 kg)
|
|
Vibration
|
ISTA 1A in carton
(International Safe Transit Association)
|
|
Regulatory compliance
|
|
Safety
|
CE, c-UL, UL
|
|
EMI/EMC
|
CE, C-tick, FCC Class A, ICES,
VCCI
|
|
Environmental
|
Complies with the appropriate
requirements of RoHS, WEEE.
|
|
Warranty
|
3 years parts and labor
|
|
NOTE
|
All nominal levels are at ±10%.
|
|
