| Extron DTP T UWP 332D Long Distance Two Input DTP
Transmitter for HDMI and VGA - Decora®
Wallplate |
Product Code:
DTPTUWP332D
 |
| The Extron DTP T UWP 332 D is a
two input Decora®-style transmitter for sending HDMI or analog
video, audio, and control up to 330 feet (100 meters) over a
shielded CATx cable to Extron DTP 330-enabled products. The
transmitter provides one HDMI input and one VGA input, both with
independent analog stereo audio connections. The DTP T UWP 332 D
supports computer video up to 1920x1200, including 1080p/60 and 2K.
It digitizes incoming analog video for reliable display on a
variety of output devices. Integrator-friendly features include
EDID Minder®, auto-switching between inputs, remote power
capability, and bidirectional RS-232 and IR pass-through for remote
AV device control. The wall-mountable design of the DTP T UWP 332 D
provides the convenience of placing input connections precisely
where they are needed. |
• Transmits
HDMI or analog video, control, and analog audio up to 330 feet (100
meters) over a shielded CATx cable — The DTP T UWP 332 D
provides high reliability and maximum performance on an economical
and easily installed cable infrastructure.
• Inputs: One HDMI, one VGA on 15-pin HD, two 3.5 mm stereo
mini jacks for audio
• Output: One DTP 330 twisted pair output on RJ-45
• One HDMI input and one VGA input — The DTP T UWP 332
D allows for switching between HDMI and analog video sources.
• Auto-switching between inputs — Auto-switching allows
for simple, unmanaged installation in locations such as in a
lectern or floor box. When multiple inputs are active, the
highest-numbered input with an active video signal takes
priority.
• Supports computer video up to 1920x1200, including HDTV
1080p/60 and 2K — The DTP T UWP 332 D supports digital signal
transmission up to 330 feet (100 meters) over a shielded twisted
pair cable and maintains superior image quality at the highest
resolutions.
• Compatible with CATx shielded twisted pair cable —
The DTP T UWP 332 D fully supports a maximum transmission distance
of 330 feet (100 meters) for all compatible resolutions when used
with CATx shielded twisted pair cable. Shielded twisted pair
cabling with solid center conductor sizes of 24 AWG or better is
recommended for optimal performance.
• Extron XTP DTP 24 shielded twisted pair cable is strongly
recommended for optimal performance
• Independent analog audio inputs — The DTP T UWP 332 D
provides two independent stereo analog audio connections for
simultaneous transmission over the same shielded twisted pair
cable. Analog audio is not embedded onto the digital video
signal.
• Supports multiple embedded audio formats — The DTP T
UWP 332 D is compatible with a broad range of multi-channel audio
signals, providing reliable operation with HDMI sources.
• Bidirectional RS-232 and IR pass-through for AV device
control — Bidirectional RS-232 control and IR signals can be
transmitted alongside the video signal, allowing remote AV devices
to be controlled without the need for additional cabling.
• Remote power capability — For simplified
installation, the transmitter can be remotely powered by a DTP
330-enabled product over the twisted pair connection.
• Digital conversion of analog input signals — Analog
signals are digitized, ensuring that a reliable, high quality
digital video signal is sent to the output destination.
• HDCP compliant — Fully supports HDCP-encrypted
sources, with selectable authorization for unencrypted content.
• Supported HDMI specification features include data rates up
to 6.75 Gbps, 3D, and HD lossless audio formats
• EDID Minder® automatically manages EDID communication
between connected devices — EDID Minder ensures that all
sources power up properly and reliably output content for
display.
• Supports EDID and HDCP transmission — DDC channels
are actively buffered, allowing continuous communication between
source and display.
• RS-232 control port — Enables the use of serial
commands for complete control and configuration via the Extron
Windows®-based control program, or integrated into a control
system. Extron products use the SIS™ - Simple Instruction Set
command protocol, a set of basic ASCII commands that allow for
quick and easy programming.
• Contact closure control port — Can be used for
external control of input switching.
• Front panel USB configuration port
• LED indicators for signal presence, HDCP, and power —
Provides visual indication of system status for real-time feedback
and monitoring of key performance parameters.
• RJ-45 signal and link LED indicators for DTP port —
Provides a means for validating signal flow and operation, allowing
quick identification of connectivity issues.
• Compatible with all DTP 330 Series receivers and DTP
330-enabled products — Enables mixing and matching with
desktop and wallplate receivers, as well as other DTP 330-enabled
products to meet application requirements.
• Mounts in an included two-gang Decora®-style wallplate
— The two-gang Decora-style wallplate is available in black
or white to blend with a wide range of environments.
• Includes LockIt® HDMI cable lacing brackets
• Highly reliable, energy-efficient external universal power
supply included |
| NOTE |
*Appropriate HDMI to DVI-D cables or adapters
are required for DVI signal input/output. |
|
| Video |
| Maximum data
rate |
6.75 Gbps (2.25 Gbps per color) |
| Maximum pixel
clock |
165 MHz |
| Resolution
range |
Up to 1920x1200 or 1080p @ 60 Hz; 8 bit color depth
2048x1080p @ 60 Hz (2K) |
| Formats |
RGB and YCbCr digital video |
| Standards |
DVI 1.0, HDMI, HDCP 1.2, EDID 1.3,
CEA-861E |
| Video input — HDMI |
| Number/signal
type |
1 single link HDMI (or DVI-D*) input |
| Connectors |
1 female HDMI type A |
| Video input — VGA |
| Number/signal
type |
1 analog RGBHV |
| Connectors |
1 female 15-pin HD (RGB) |
| Nominal
level |
0.7 Vp-p for RGB |
| Minimum/maximum
levels |
0.3 V to 1.45 Vp-p |
| Impedance |
75 ohms |
| Horizontal
frequency |
15 kHz to 130 kHz |
| Vertical
frequency |
30 Hz to 150 Hz |
|
Return
loss |
<-30 dB @ 5 MHz |
| DC offset (max.
allowable) |
250 mV |
| Interconnection between transmitter and
receiver |
| Signal
type |
1 DTP 330 output |
| Connectors |
1 female RJ-45 |
| Termination
standards |
TIA/EIA T568B |
| DTP
signal |
|
| Signal
transmission distance |
Up to 330' (100 m) using shielded twisted pair (STP) cable
or XTP DTP 24 cable |
| Cable
requirements |
Solid conductor, 24 AWG or better |
| Cable
recommendations |
400 MHz bandwidth STP cable |
| NOTE |
Extron XTP DTP 24 shielded twisted pair cable is
strongly recommended for optimal performance. |
|
| Audio |
| Gain |
Unbalanced output: 0 dB; balanced output +6
dB |
| Frequency
response |
20 Hz to 20 kHz, ±0.5 dB |
| THD +
Noise |
0.03% @ 20 Hz to 20 kHz at maximum output |
| S/N |
>90 dB, at maximum output (15 dBu), balanced
(unweighted) |
| Stereo channel
separation |
>80 dB @ 1 kHz to 20 kHz |
| Audio input |
| Number/signal
type |
|
| Analog
audio (over DTP) |
2 stereo, unbalanced |
| NOTE |
Analog audio is not embedded onto the digital
video signal. |
|
| Digital
audio |
1 embedded digital audio on DTP |
| Embedded
digital audio source formats |
2-ch PCM, PCM, Dolby Digital 2/0, Dolby Digital 2/0
Surround, Dolby Digital 5.1, Dolby Digital EX, DTS Digital Surround
5.1, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1 |
| Connectors |
(2) 3.5 mm stereo jack, 2 channel; tip (L); ring (R);
sleeve (ground) |
| Impedance |
>10k ohms, DC coupled |
| Nominal
level |
-10 dBV (316 mVrms) |
| Maximum
level |
+7 dBu, unbalanced |
| NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈
2 dBu |
|
| Audio output |
| Number/signal
type |
|
| Analog
audio (over DTP) |
1 stereo, unbalanced |
| Digital
audio |
1 embedded digital audio on DTP |
| Embedded
digital audio source formats |
2-ch PCM, PCM, Dolby Digital 2/0, Dolby Digital 2/0
Surround, Dolby Digital 5.1, Dolby Digital EX, DTS Digital Surround
5.1, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1 |
| Connectors |
1 female RJ-45 jack |
| Communications —
transmitter |
| Serial control
port |
RS-232 via (1) 3.5 mm, 5-pole captive screw connector for
RS-232 control (±5 V) and contact closure input
switching |
| Baud rate and
protocol |
9600 baud rate, 8 data bits, 1 stop bit, no
parity |
| Contact closure
remote control |
(1) 3.5 mm, 5-pole captive screw connector
(connector is shared with RS-232 control port) |
| USB control
port |
1 front panel female mini USB type B |
| USB
standards |
USB 2.0, high speed |
| Program
control |
Extron Simple Instruction Set (SIS™) |
| Communications — external device
(pass-through) |
| Serial control
pass-through port |
Bidirectional RS-232 |
| Connector |
|
| DTP
output |
(1) 3.5 mm captive screw connector, 5-pole |
| Baud
rates |
300 to 38.4k baud |
| Protocol |
Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none |
| IR pass-through
control port |
TTL level (0 to 5 V) modulated infrared control from 30
kHz up to 60 kHz |
| DTP
output |
(1) 3.5 mm captive screw connector, 2-pole |
| NOTE |
Protocol is mirrored between the connected DTP 230
or DTP 330 endpoints and the "Over DTP" ports on the DTP T UWP 332
D. Signals from a control device pass into each "Over DTP" port,
are embedded with the DTP signal, and sent to the individual
endpoints for control of remote sink or source
devices. |
|
| General |
| Power
supply |
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts |
| Power
consumption |
|
| Transmitter |
|
| Device |
4.8 watts, 12 VDC |
| Device
and power supply |
6.3 watts, 100-240 VAC, 50-60 Hz |
| NOTE |
Each transmitter or receiver can be powered either
locally by an external power supply or remotely by receiver or
transmitter on the other end of the twisted
pair cable. |
|
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to
90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%,
noncondensing |
| Cooling |
Convection, no vents |
| Thermal
dissipation |
|
| Transmitter |
|
| Device |
15.3 BTU/hr |
| Device
and power supply |
20.1 BTU/hr |
| Mounting |
|
| Rack
mount |
Yes, with included rack ears |
| Enclosure
type |
Metal |
| Enclosure
dimensions |
|
| Faceplate |
Two [2.6" H* x 1.3" W x 0.2" D
(6.6 cm H x 3.3 cm W x 0.6 cm D)]
(Fits the opening in a 2 gang Decora©-style
wallplate.) |
| Device |
Two (2.7" H x 3.5" W x 1.9" D
[6.9 cm H x 8.9 cm W x 4.8 cm D]) |
| NOTE |
*Height is 4.2" (10.4 cm) including mounting
tabs. |
|
| Product
weight |
0.4 lbs (0.2 kg) |
| Shipping
weight |
1.8 lbs (0.8 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit
Association) |
| Regulatory
compliance |
|
| Safety |
c-UL, UL |
| EMI/EMC |
AS/NZS, CE**, FCC Class A**, ICES, VCCI |
| Environmental |
Complies with the appropriate requirements of RoHS,
WEEE |
| NOTE |
**CE and FCC testing is conducted with STP
cable. |
|
| Warranty |
3 years parts and labor |
| NOTE |
All nominal levels are at
±10%. |
|
|
| |
|
|
| |
|
|
