| NOTE |
This product consists of a transmitter (DTP DP 330
Tx) and a receiver (DTP DP 330 Rx), sold separately, with a twisted
pair cable linking the transmitter and receiver. |
|
| Video |
| Maximum data
rate |
Up to 10.8 Gbps (2.7 Gbps per lane) |
| Maximum pixel
clock |
300 MHz |
| Resolution
range |
Up to 2560x1600 @ 60Hz or 3840x2160 @ 30 Hz, 4k @
30Hz |
| Color bit
depth |
12 bits for resolutions up to 1080p. 10 bits for all
resolutions above 1080p. |
| Formats |
RGB and YCbCr digital video |
| Standard |
DisplayPort 1.1a |
| Video input — transmitter |
| Number/signal
type |
1 DisplayPort |
| Connector |
1 female DisplayPort |
| Interconnection between transmitter and
receiver |
| Signal
type |
DTP 330 |
| Connector |
1 female RJ-45 per unit |
| Termination
standard |
TIA/EIA T568B |
| Signal transmission
distance |
Up to 330' (100 m) using shielded twisted pair cable or
XTP DTP 24 STP cable |
| Cable
requirements |
Solid conductor, 24 AWG or better |
| Cable
recommendations |
400 MHz bandwidth, STP (shielded twisted
pair) |
| NOTE |
Extron XTP DTP 24 shielded twisted pair
cable is strongly recommended for optimal
performance. |
|
| Video output — receiver |
| Number/signal
type |
1 DisplayPort |
| Connectors |
1 female DisplayPort |
| Audio |
| Gain |
Unbalanced output: 0 dB; balanced output +6
dB |
| Frequency
response |
20 Hz to 20 kHz, ±0.5 dB |
| THD +
Noise |
0.03% @ 20 Hz to 20 kHz at maximum output |
| S/N |
>90 dB, at maximum input (unweighted) |
| Stereo channel
separation |
>80 dB |
|
Digital
sampling |
48 kHz |
| Bit
depth |
16 bit |
| Audio input |
| Signal
type |
|
| Analog
audio (over DTP) |
Stereo (2 channel), balanced/unbalanced |
| NOTE |
Analog audio is not embedded onto the DisplayPort
signal. Embedded digital audio is not de-embedded from
the DisplayPort signal. |
|
| Digital
audio |
Embedded digital audio on DTP signal |
| Embedded
digital audio source formats |
2-ch PCM, PCM, Dolby Digital 2/0 Surround, Dolby Digital
2/0, DTS Digital Surround 5.1, DTSES Matrix 6.1, DTS-ES Discrete
6.1 |
| Connector |
(1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R),
sleeve (ground) |
| Impedance |
>10k ohms, DC coupled |
| Nominal
level |
-10 dBV (316 mVrms) |
| Maximum
level |
+7 dBV (unbalanced) |
| NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0
dBV ≈ 2 dBu |
|
| Audio output |
| Signal
type |
|
| Analog
audio (over DTP) |
Stereo (2 channel), balanced/unbalanced |
| NOTE |
Analog audio is not embedded onto the DisplayPort
signal. Embedded digital audio is not de-embedded from
the DisplayPort signal. |
|
| Digital
audio |
Embedded digital audio on DTP signal |
| Embedded
digital audio source formats |
2-ch PCM, PCM, Dolby Digital 2/0 Surround, Dolby Digital
2/0, DTS Digital Surround 5.1, DTSES Matrix 6.1, DTS-ES Discrete
6.1 |
| Impedance |
50 ohms unbalanced, 100 ohms balanced |
| Gain
error |
±0.2 dB channel to channel |
| Maximum level (600
ohm) |
>+14 dBu, balanced |
| Connectors |
|
| Digital
audio |
Female DisplayPort |
| Analog
audio |
(1) 3.5 mm captive screw connector, 5 pole |
| Communications — external device
(pass-through, unidirectional or bidirectional) |
| Serial control port
input/output |
|
| Transmitter |
RS-232 via (1) 3.5 mm, 5 pole captive screw connector for
RS-232 control (±5 V) (connector is shared with IR control
port) |
| Receiver |
1 set of proprietary signals on a female RJ-45
jack |
| Serial control port
output/input |
|
| Transmitter |
1 set of proprietary signals on a female RJ-45
jack |
| Receiver |
RS-232 via a 3.5 mm, 3 pole captive screw
connector |
| Baud
rates |
Up to 115200 baud |
| Protocol |
Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none |
| Serial control pin
configuration |
1 = Tx, 2 = Rx, 3 = Gnd |
| IR control
port |
(1) 3.5 mm, captive screw connector, 5 pole (connector is
shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up
to 60 kHz |
| IR control pin
configuration |
3 = Gnd, 4 = IR Tx, 5 = IR Rx |
| General |
| Power
supply |
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts |
| Power
consumption |
|
| Transmitter |
|
| Device |
TBD watts, 12 VDC |
| Device
and power supply |
TBD watts, 100-240 VAC, 50-60 Hz |
| Receiver |
|
| Device |
TBD watts, 12 VDC |
| Device
and power supply |
TBD watts, 100-240 VAC, 50-60 Hz |
| NOTE |
Each transmitter or receiver can be powered either
locally by an external power supply or remotely by receiver or
transmitter on the other end of the twisted
pair cable. |
|
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to
90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%,
noncondensing |
| Cooling |
Convection, no vents |
| Thermal
dissipation |
|
| Transmitter |
|
| Device |
TBD BTU/hr |
| Device
and power supply |
TBD BTU/hr |
| Receiver |
|
| Device |
TBD BTU/hr |
| Device
and power supply |
TBD BTU/hr |
|
Mounting |
| Rack
mount |
Yes, with optional 1U high rack shelf |
| Furniture
mount |
Yes, with optional under-desk mounting kit |
| Enclosure
type |
Metal |
| Enclosure
dimensions |
|
| Transmitter |
1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors.) |
| Receiver |
1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product
weight |
|
| Transmitter |
0.5 lbs (0.3 kg) |
| Receiver |
1.0 lb (0.5 kg) |
| Shipping
weight |
3 lbs (2 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit
Association) |
| Regulatory
compliance |
|
| Safety |
CE, c-UL, UL |
| EMI/EMC |
CE**, C-tick, FCC Class A**, ICES, VCCI |
| NOTE |
**CE and FCC testing is conducted with STP
(shielded twisted pair) I/O cable. |
|
| Warranty |
3 years parts and labor |
| NOTE |
All nominal levels are at
±10%. |
|
