| Extron DTP T USW 333 Three Input Switcher with Integrated
Long Distance DTP Transmitter |
Product Code:
DTPTUSW333
 |
| The Extron DTP T USW 333 is a
three input switcher for sending HDMI or analog video, audio, and
control up to 330 feet (100 meters) over a shielded CATx cable to
Extron DTP 330-enabled products. It is HDCP compliant and provides
two HDMI inputs, one VGA or component video input, and one DTP 330
twisted pair output. The DTP T USW 333 supports computer-video to
1920x1200, including 1080p/60 Deep Color and 2K. It digitizes
incoming analog video for reliable display on a variety of output
devices. The switcher also offers many integrator-friendly features
such as EDID Minder®, auto-switching between inputs, audio
input assignment, and remote power capability. These features, plus
the low profile enclosure, make the DTP T USW 333 ideal for
discreet placement in lecterns, beneath tables, or wherever needed
to meet application requirements. |
• Transmits
HDMI or analog video, control, and analog audio up to 330 feet (100
meters) over a shielded CATx cable — The DTP T USW 333
provides high reliability and maximum performance on an economical
and easily installed cable infrastructure.
• Inputs: Two HDMI, one VGA or component video on 15-pin HD,
one 3.5 mm stereo mini jack for audio
• Output: One DTP 330 twisted pair output on RJ-45
• Two HDMI inputs and one VGA or component video input
— The DTP T USW 333 allows for switching between HDMI and
analog video sources.
• Auto-switching between inputs — Auto-switching allows
for simple, unmanaged installation in locations such as in a
lectern or under a conference table. When multiple inputs are
active, the switching priority is configurable.
• Supports computer-video to 1920x1200, including HDTV
1080p/60 Deep Color and 2K — The DTP T USW 333 supports
digital signal transmission up to 330 feet (100 meters) over a
shielded twisted pair cable and maintains superior image quality at
the highest resolutions.
• Compatible with CATx shielded twisted pair cable —
The DTP T USW 333 fully supports a maximum transmission distance of
330 feet (100 meters) for all compatible resolutions when used with
CATx shielded twisted pair cable. Shielded twisted pair cabling
with solid center conductor sizes of 24 AWG or better is
recommended for optimal performance.
• Extron XTP DTP 24 shielded twisted pair cable is strongly
recommended for optimal performance
• Accepts additional analog stereo audio signals — The
DTP T USW 333 supports a direct pass-through connection for stereo
analog audio signals for simultaneous transmission over the same
shielded twisted pair cable. Analog audio is not embedded onto the
digital video signal.
• Audio input assignment — The analog audio input can
be assigned to any video input, or it can be set to follow the
input switch.
• Supports multiple embedded audio formats — The DTP T
USW 333 is compatible with a broad range of multi-channel audio
signals, providing reliable operation with HDMI sources.
• Bidirectional RS-232 and IR pass-through for AV device
control — Bidirectional RS-232 control and IR signals can be
transmitted alongside the video signal, allowing remote AV devices
to be controlled without the need for additional cabling.
• Remote power capability — For simplified
installation, the transmitter can be remotely powered by a DTP
330-enabled product over the twisted pair connection.
• Digital conversion of analog input signals — Analog
signals are digitized, ensuring that a reliable, high quality
digital video signal is sent to the output destination.
• HDCP compliant
• Supported HDMI specification features include data rates up
to 6.75 Gbps, Deep Color up to 12-bit, 3D, and HD lossless audio
formats
• EDID Minder® automatically manages EDID communication
between connected devices — EDID Minder ensures that all
sources power up properly and reliably output content for
display.
• Supports EDID and HDCP transmission — DDC channels
are actively buffered, allowing continuous communication between
source and display.
• Front panel security lockout — This feature locks out
all front panel functions; all functions however, are available
through USB or RS-232 control.
• RS-232 control port — Enables the use of serial
commands for complete control and configuration via the Extron
Windows®-based control program, or integrated into a control
system. Extron products use the SIS™ - Simple Instruction Set
command protocol, a set of basic ASCII commands that allow for
quick and easy programming.
• Contact closure remote control with tally output —
Allows for remote selection of an input channel, while a tally
output provides +5 VDC to light an LED to indicate the currently
selected input.
• Front panel USB configuration port — Enables easy
configuration without having to access the rear panel.
• LED indicators for signal presence, HDCP, and power —
Provides visual indication of system status for real-time feedback
and monitoring of key performance parameters.
• RJ-45 signal and link LED indicators for DTP port —
Provides a means for validating signal flow and operation, allowing
quick identification of connectivity issues.
• Compatible with all DTP 330 Series receivers and DTP
330-enabled products — Enables mixing and matching with
desktop and wallplate receivers, as well as other DTP 330-enabled
products to meet application requirements.
• Easy setup and commissioning with Extron's PCS - Product
Configuration Software — Conveniently configure multiple
products using a single software application.
• 1" (2.5 cm) high, half rack width metal enclosure —
With a low profile enclosure, the device can be installed
discreetly wherever needed.
• Includes LockIt® HDMI cable lacing brackets
• Highly reliable, energy-efficient external universal power
supply included
|
| Video |
| VGA |
|
| Gain |
Unity |
| Bandwidth |
170 MHz (-3 dB) |
| Crosstalk |
-50 dB @ 10 MHz, -30 dB @ 100 MHz |
| Switching
speed |
<5 ms. (max) |
| HDMI |
|
| Maximum
data rate |
6.75 Gbps (2.25 Gbps per color) |
| Maximum
pixel clock |
165 MHz |
| Resolution
range |
Up to 1920x1200 or 1080p @ 60 Hz; 2k |
| Formats |
RGB and YCbCr digital video |
| Standards |
DVI 1.0, HDMI, HDCP 1.1, CEA-861E |
| Video input — HDMI |
| Number/signal
type |
2 HDMI inputs (or single-link DVI-D with the appropriate
DVI-HDMI adapters) |
| Connectors |
2 female HDMI type A |
| Video input — VGA |
| Number/signal
type |
1 VGA-QXGA; RGBHV; Y, R-Y, B-Y |
| Connectors |
1 female 15-pin HD |
| Nominal
level |
1 Vp-p for Y of YUV
0.7 Vp-p for RGB, R-Y, and B-Y |
| Min./max.
level |
Analog, 0.3 V to 1.5 Vp-p with no offset |
| Impedance |
75 ohms |
| Horizontal
frequency |
15 kHz to 145 kHz |
| Vertical
frequency |
30 Hz to 170 Hz |
| Return
loss |
<-40 dB @ 5 MHz |
| NOTE |
The VGA input is digitized and output as DTP. The
VGA signal is not scaled. |
|
| Sync — VGA |
| Input
type |
RGBHV, bi-level and tri-level sync |
| Input
level |
1.9 V to 5.0 Vp-p |
| S/N |
>90 dB at maximum input (unweighted) |
| Max. input
voltage |
5.0 Vp-p |
| Interconnection between transmitter and
receiver |
| Number/signal
type |
1 DTP 330 output |
| Connector |
1 female RJ-45 |
| Termination
standard |
TIA/EIA T568B |
| Transmission
distance |
Up to 330' (100 m) using shielded twisted pair cable or
XTP DTP 24 STP cable |
| Cable
requirements |
Solid conductor, 24 AWG or better |
| Cable
recommendations |
400 MHz bandwidth, STP (shielded twisted
pair) |
| NOTE |
Extron XTP DTP 24 shielded twisted pair cable is
strongly recommended for optimal performance. |
|
| Audio |
| Gain |
Unbalanced output: 0 dB; balanced output +6
dB |
| Frequency
response |
20 Hz to 20 kHz, ±0.5 dB |
| THD +
Noise |
0.01% @ 1 kHz at nominal level |
| S/N |
>90 dB, at maximum input (unweighted) |
| Crosstalk |
<-45 dB @ 20 kHz, or -72 dB @ 1 kHz or
below |
| Stereo channel
separation |
>80 dB @ 1 kHz to 20 kHz |
| Audio input |
| Number/signal
type |
1 analog stereo, unbalanced or
2-digital audio, embedded in the HDMI |
| NOTE |
Analog audio is not embedded onto the digital
video signal. |
|
| Connectors |
1 female 3.5 mm mini stereo jack
2 female HDMI Type A (shared with video input) |
| Source
formats |
|
| HDMI |
LPCM up to 7.1/24-bit/192 kHz, Dolby TrueHD, Dolby Digital
Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby Digital 2/0
Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS-ES
Discrete 6.1, DTS-ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2
Channel |
| Analog |
Analog stereo audio |
| Impedance |
10k ohms, DC coupled |
| Nominal
level |
-10 dBV |
| Maximum
level |
+6dBV, unbalanced |
| CMRR |
>60 dB typ @ 1 kHz |
| Input gain
adjustment |
-18 dB to +24 dB, 1 dB steps, adjustable per
input |
| NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0
dBV ≈ 2 dBu |
|
| Audio output |
| Number/signal
type |
1 analog audio over DTP signal, or
1 embedded digital audio over DTP signal |
| Connectors |
1 RJ-45 jack |
|
| Control/remote — switcher |
| Serial control
port |
RS-232 via (1) 3.5 mm, 3 pole captive screw
connector |
| Serial control pin
configuration |
Pin 1 = Tx, pin 2 = Rx, pin 3 = Gnd |
| Baud rate and
protocol (RS-232) |
9600 baud, 8 data bits, 1 stop bit, no
parity |
| Tally
port |
(1) 3.5 mm, 4 pole captive screw connector |
| Tally port pin
configuration |
Pin 1 = input 1 tally, pin 2 = input 2 tally, pin 3 =
input 3 tally, pin 4 = +5 VDC |
| Contact closure
remote control |
(1) 3.5 mm, 4 pole captive screw connector |
| Contact closure pin
configuration |
Pin 1 = input 1, pin 2 = input 2, pin 3 = input 3, pin 4 =
Gnd |
| USB control
port |
1 front panel female mini USB, type B |
| USB
standards |
USB 2.0, high speed |
| Program
control |
Extron Simple Instruction Set
(SISTM) |
| Control/remote — (RS-232/IR over
DTP) |
| NOTE |
Protocol is mirrored between the connected DTP 330
Rx and the Over DTP output port. Signals from a control device pass
into the Over DTP port, are embedded with the DTP signal, and
sent to the DTP 330 Rx endpoint for control of remote sink and
source devices.
The Over DTP port is a pass-through connection to the DTP endpoint.
There is no RS-232 or IR insertion from the DTP T USW 333 control
port to the Over DTP port. |
|
| Serial control
pass-through port |
1 RS-232 and IR via (1) 3.5 mm, 5-pole captive screw
connector |
| Serial control pin
configuration |
Pin 1 = Tx, pin 2 = Rx, pin 3 = Gnd |
| Baud
rates |
300 to 38400 baud |
| Protocol |
8 or 7 data bits
1 or 2 stop bits
no parity (default)
even or odd parity |
| IR pass-through
control port |
TTL level (0 to 5 V) modulated infrared control from 30
kHz up to 60 kHz |
| IR control pin
configuration |
3 = GND, 4 = IR Tx, 5 = IR Rx |
| General |
| Power
supply |
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts |
| Power
consumption |
|
| Device |
5.5 watts |
| Device
and power supply |
7.2 watts |
| NOTE |
The DTP T USW 333 can be powered either locally
by the external power supply or remotely by a receiver on the
other end of the twisted pair cable. |
|
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to
90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%,
noncondensing |
| Cooling |
Convection, vents on top and sides |
| Thermal
dissipation |
|
| Device |
15.4 BTU/hour |
| Device
and power supply |
21.0 BTU/hour |
|
Mounting |
| Rack
mount |
Yes, with optional 1U high rack shelf |
| Furniture
mount |
Yes, with optional under-desk mounting kit |
| Enclosure
type |
Metal |
| Enclosure
dimensions |
1.0" H x 8.75" W x 6.0" D (half rack wide)
(2.5 cm H x 22.2 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product
weight |
0.6 lbs (0.3 kg) |
| Shipping
weight |
2 lbs (1 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit
Association) |
| Regulatory
compliance |
|
| Safety |
CE, c-UL, UL |
| EMI/EMC |
CE**, C-tick, FCC Class A**, ICES, VCCI |
| Environmental |
Complies with the appropriate requirements of RoHS,
WEEE |
| NOTE |
**CE and FCC testing is conducted with STP
(shielded twisted pair) I/O cable. |
|
| Warranty |
3 years parts and labor |
| NOTE |
All
nominal levels are at ±10%. |
|
|
| |
|
|
| |
|
|
