| NOTE |
*Appropriate HDMI to DVI-D cables
or adapters are required for HDMI signal
input/output. |
|
| Video |
| Maximum data
rate |
10.2 Gbps (3.4 Gbps per color) |
| Maximum pixel
clock |
300 MHz |
| Resolution
range |
1920x1200 or 1080p @ 60 Hz; 8, 10, or 12 bit color
depth
4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz |
| Formats |
RGB and YCbCr digital video |
| Standards |
DVI 1.0, HDMI, HDCP |
| Video input — transmitter |
| Number/signal
type |
1 single link HDMI (or DVI-D*) input |
| Connectors |
1 female HDMI type A |
| Interconnection between transmitter and
receiver |
| Connectors |
1 female RJ-45 per unit for 1 cable connecting the
transmitter and receiver |
| Termination
standards |
TIA/EIA T568B |
| DTP signal |
|
| Signal
transmission distance |
Up to 330' (100 m) using shielded twisted pair (STP) cable
or XTP DTP 24 cable |
| Cable
requirements |
Solid conductor, 24 AWG or better |
| Cable
recommendations |
400 MHz bandwidth STP cable |
| NOTE |
Extron XTP DTP 24 shielded twisted pair cable is
strongly recommended for optimal performance. |
|
| Video output — receiver |
| Number/signal
type |
1 single link HDMI (or DVI-D*) |
| Connectors |
1 female HDMI type A |
| Audio |
| Gain |
Unbalanced output: 0 dB |
| Frequency
response |
20 Hz to 20 kHz, ±1 dB |
| THD + Noise |
0.03% @ 1 kHz at nominal level, 0.3% @ 20 kHz at nominal
level |
| S/N |
>90 dB, at maximum output (unweighted) |
| Stereo channel
separation |
>80 dB @ 1 kHz to 20 kHz |
| Audio input — transmitter |
| Number/signal
type |
1 PC level stereo, unbalanced |
| NOTE |
Analog audio is not embedded onto the digital
video signal. Embedded digital audio is not de-embedded from the
digital video signal. |
|
| Connectors |
(1) 3.5 mm stereo jack, 2 channel; tip (L); ring (R);
sleeve (ground) |
| Impedance |
20k ohms, DC coupled |
| Nominal level |
-10 dBV (316 mVrms) |
| Maximum level |
+6 dBu, unbalanced |
| NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈
2 dBu |
|
| Audio output — receiver |
| Number/signal
type |
1 stereo (2 channel), unbalanced |
| Connectors |
(1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R),
sleeve (ground) |
| Impedance |
50 ohms, unbalanced |
| Gain error |
±0.2 dB channel to channel |
| Maximum level (600
ohm) |
>+7 dBu, unbalanced at 1% THD+N |
| Control/remote — external device
(pass-through, unidirectional or bidirectional) |
| Serial control port
input |
|
| Transmitter |
RS-232 via (1) 3.5 mm, 5 pole captive screw connector
(connector is shared with IR control port) |
| Receiver |
1 set of proprietary signals on a female RJ-45
jack |
| Serial control port
output |
|
| Transmitter |
1 set of proprietary signals on a female RJ-45
jack |
| Receiver |
RS-232 via a 3.5 mm, 5 pole captive screw
connector |
| NOTE |
Protocol is mirrored between the transmitter and
the receiver. |
|
| Baud rates |
300 baud through 38.4 kbaud |
| Protocol |
8 or 7 data bits
1 or 2 stop bits
no parity (default)
even or odd parity |
| Serial control pin
configuration |
Captive screw connectors: 1 = Tx, 2 = Rx, 3 =
Gnd |
| IR control
port |
(1) 3.5 mm, captive screw connector, 5 pole (connector is
shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to
60 kHz |
| IR control pin
configuration |
3 = Gnd, 4 = IR Tx, 5 = IR Rx |
| General |
| Power supply |
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts |
| Power
consumption |
|
| Transmitter |
|
| Device |
2.8 watts, 12 VDC |
| Device
and power supply |
3.8 watts, 100-240 VAC, 50-60 Hz |
| Receiver |
|
| Device |
4.2 watts, 12 VDC |
| Device
and power supply |
5.9 watts, 100-240 VAC, 50-60 Hz |
| NOTE |
Each transmitter or receiver can be powered either
locally by an external power supply or remotely by receiver or
transmitter on the other end of the twisted
pair cable. |
|
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to
90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%,
noncondensing |
| Cooling |
Convection, no vents |
| Thermal
dissipation |
|
| Transmitter |
|
| Device |
8.3 BTU/hr |
| Device
and power supply |
11.8 BTU/hr |
| Receiver |
|
| Device |
13.1 BTU/hr |
| Device
and power supply |
18.8 BTU/hr |
| Mounting |
|
| Furniture
or wall mount |
Yes, with a 2 gang wall box or mud ring |
| Enclosure type |
Metal |
| Enclosure
dimensions |
|
| Faceplate |
2.6" H x 2.6" W x 0.1" D
(6.6 cm H x 6.6 cm W x 0.3 cm D)
(Fits the opening in a 2 gang Decora©-style
wallplate.) |
| Device |
2.7" H x 3.5" W x 1.8" D
(6.9 cm H x 8.7 cm W x 4.5 cm D) |
| NOTE |
Height excludes mounting tabs, depth excludes
connectors. |
|
| Product weight |
0.4 lbs (0.2 kg) |
| Shipping
weight |
2 lbs (1 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit
Association) |
| Regulatory
compliance |
|
| Safety |
CE, c-UL, UL |
| EMI/EMC |
CE**, C-tick, FCC Class A**, ICES, KC, VCCI |
| NOTE |
**CE and
FCC testing is conducted with STP cable. |
|
| Warranty |
3 years parts and labor |
| NOTE |
All nominal levels are at
±10% |
|
