| NOTE |
*Appropriate HDMI to DVI-D cables or adapters
are required for DVI signal input/output. |
|
| Video |
| Maximum data
rate |
6.75 Gbps (2.25 Gbps per color) |
| Maximum pixel
clock |
165 MHz |
| Resolution
range |
Up to 1920x1200 or 1080p @ 60 Hz; 8 bit color depth
2048x1080p @ 60 Hz (2K) |
| Formats |
RGB and YCbCr digital video |
| Standards |
DVI 1.0, HDMI, HDCP 1.2, EDID 1.3,
CEA-861E |
| Video input |
| Number/signal
type |
2 single link HDMI (or DVI-D*) input |
| Connectors |
2 female HDMI type A |
| Interconnection between transmitter and
receiver |
| Signal
type |
1 DTP 230 output |
| Connectors |
1 female RJ-45 per unit for 1 cable connecting the
transmitter and receiver |
| Termination
standards |
TIA/EIA T568B |
| DTP
signal |
|
| Signal
transmission distance |
Up to 230' (70 m) using shielded twisted pair (STP) cable
or XTP DTP 24 cable |
| Cable
requirements |
Solid conductor, 24 AWG or better |
| Cable
recommendations |
400 MHz bandwidth STP cable |
| NOTE |
Extron XTP DTP 24 shielded twisted pair cable is
strongly recommended for optimal performance. |
|
| Audio |
| Gain |
Unbalanced output: 0 dB; balanced output +6
dB |
| Frequency
response |
20 Hz to 20 kHz, ±0.5 dB |
| THD +
Noise |
0.03% @ 20 Hz to 20 kHz at maximum output |
| S/N |
>90 dB, at maximum output (15 dBu), balanced
(unweighted) |
| Stereo channel
separation |
>90 dB @ 1 kHz to 20 kHz |
| Audio input |
| Number/signal
type |
|
| Analog
audio (over DTP) |
2 stereo, unbalanced |
| NOTE |
Analog audio is not embedded onto the digital
video signal. |
|
| Digital
audio |
2 embedded digital audio on DTP |
| Embedded
digital audio source formats |
2-ch PCM, PCM, Dolby Digital 2/0, Dolby Digital 2/0
Surround, Dolby Digital 5.1, Dolby Digital EX, DTS Digital Surround
5.1, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1 |
| Connectors |
(2) 3.5 mm stereo jack, 2 channel; tip (L); ring (R);
sleeve (ground) |
| Impedance |
>10k ohms, DC coupled |
| Nominal
level |
-10 dBV (316 mVrms) |
| Maximum
level |
+7 dBu, unbalanced |
| NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈
2 dBu |
|
| Audio output |
| Number/signal
type |
|
| Analog
audio (over DTP) |
1 stereo, unbalanced |
| Digital
audio |
1 embedded digital audio on DTP |
| Embedded
digital audio source formats |
2-ch PCM, PCM, Dolby Digital 2/0, Dolby Digital 2/0
Surround, Dolby Digital 5.1, Dolby Digital EX, DTS Digital Surround
5.1, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1 |
| Connectors |
1 female RJ-45 jack |
| Communications —
transmitter |
| Serial control
port |
RS-232 via (1) 3.5 mm, 5-pole captive screw connector for
RS-232 control (±5 V) and contact closure input
switching |
| Baud rate and
protocol |
9600 baud rate, 8 data bits, 1 stop bit, no
parity |
| Contact closure
remote control |
(1) 3.5 mm, 5-pole captive screw connector (connector is
shared with RS-232 control port) |
| USB control
port |
1 front panel female mini USB type B |
| USB
standards |
USB 2.0, high speed |
| Program
control |
Extron Simple Instruction Set (SIS™) |
| Communications — external device
(pass-through) |
| Serial control
pass-through port |
Bidirectional RS-232 |
| Connector |
|
| DTP
output |
(1) 3.5 mm captive screw connector, 5-pole |
| Baud
rates |
300 to 38.4k baud |
| Protocol |
Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none |
| IR pass-through
control port |
TTL level (0 to 5 V) modulated infrared control from 30
kHz up to 60 kHz |
| DTP
output |
(1) 3.5 mm captive screw connector, 2-pole |
| NOTE |
Protocol is mirrored between the connected DTP 230
or DTP 330 endpoints and the "Over DTP" ports on the DTP T HWP 232
D. Signals from a control device pass into each "Over DTP" port,
are embedded with the DTP signal, and sent to the individual DTP
230 Tx or Rx endpoints for control of remote sink or source
devices. |
|
| General |
| Power
supply |
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts |
| Power
consumption |
|
| Transmitter |
|
| Device |
4.8 watts, 12 VDC |
| Device
and power supply |
6.3 watts, 100-240 VAC, 50-60 Hz |
| NOTE |
Each transmitter or receiver can be powered either
locally by an external power supply or remotely by receiver or
transmitter on the other end of the twisted
pair cable. |
|
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to
90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%,
noncondensing |
| Cooling |
Convection, no vents |
| Thermal
dissipation |
|
| Transmitter |
|
| Device |
15.3 BTU/hr |
| Device
and power supply |
20.1 BTU/hr |
| Mounting |
|
| Rack
mount |
Yes, with included rack ears |
| Enclosure
type |
Metal |
| Enclosure
dimensions |
|
| Faceplate |
Two (2.6" H* x 1.3" W x 0.2" D
[6.6 cm H x 3.3 cm W x 0.6 cm D])
(Fits the opening in a 2 gang Decora©-style
wallplate.) |
| Device |
Two (2.7" H x 3.5" W x 1.9" D
[6.9 cm H x 8.9 cm W x 4.8 cm D]) |
| NOTE |
*Height is 4.2" (10.4 cm) including mounting
tabs. |
|
| Product
weight |
0.4 lbs (0.2 kg) |
| Shipping
weight |
1.8 lbs (0.8 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit
Association) |
| Regulatory
compliance |
|
| Safety |
c-UL, UL |
| EMI/EMC |
AS/NZS, CE**, FCC Class A**, ICES, VCCI |
| Environmental |
Complies with the appropriate requirements of RoHS,
WEEE |
| NOTE |
**CE and FCC testing is conducted with STP
cable. |
|
| Warranty |
3 years parts and labor |
| NOTE |
All nominal levels are at
±10%. |
|
