| DPA d:dicate™ 4011F Cardioid Table, Podium or
Floor Stand Microphone |
|
Product Code:
4011F
|
|
4011-F15 |
|
Cardioid Podium Microphone, 15cm Boom |
 |
|
|
4011-F30 |
|
Cardioid Podium Microphone, 30cm Boom |
|
|
|
4011-F45 |
|
Cardioid Podium Microphone, 45cm Boom |
|
|
|
4011-F75 |
|
Cardioid Podium Microphone, 75cm Boom |
|
|
|
4011-F120 |
|
Cardioid Floor Stand Microphone, 120cm Boom |
|
|
• Low distortion
– Linear repsonse
• Huge dynamic range
• Accurate
• Transparent sound
Due to its modular nature, the MMC4011 cardioid capsule can be
combined with different lengths of podium boom poles – 15, 30
or 45 cm (6, 12 or 18 in). If longer booms are needed for floor
stands with visual elegance, our long booms at 75 or 120 cm (30 or
48 in) makes a high-quality stage voice or instrument mic together
with our dedicated accessories.
For music instruments, the 4011 capsule is a reference standard for
its low-distortion and linear approach in an unusual huge dynamic
range. With our sleek floor stands it is also a joy for the stage
designer.
For speech it’s all about the voice and no sound source is
probably as recognizable as just that. The DPA 4011F has a natural
response to speak and a noise rejecting quality. No equalization is
needed to remove any microphone artifacts, with the 4011F the voice
intelligibility is straight out of the mic. |
| Directional
pattern: |
Cardioid |
| Principle of
operation: |
Pressure
Gradient |
| Cartridge
Type: |
Pre-polarized
condenser |
| Frequency
range: |
20 Hz to 20
kHz |
| Frequency range,
± 2 dB: |
40 Hz to 20
kHz |
| Sensitivity,
nominal, ± 2 dB at 1 kHz: |
10 mV/Pa; -40 dB re. 1
V/Pa |
| Equivalent noise
level, A-weighted: |
Typ. 18 dB(A) re. 20
µPa (max. 20 dB(A)) |
| Equivalent noise
level, ITU-R BS.468-4: |
Typ. 25
dB |
| S/N ratio
(A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): |
Typ. 76
dB(A) |
| Total Harmonic
Distortion (THD) at 1 kHz: |
< 1 % up to 139 dB
SPL peak |
| Minimum load
impedance: |
2
kohm |
| Dynamic
range: |
Typ.
121dB |
| Max. SPL, peak
before clipping: |
144dB |
| Output
impedance: |
100
ohm |
| Cable drive
capability: |
100 m (328
ft) |
| Output balance
principle: |
Impedance balancing
with Active Drive |
| Common Mode
Rejection Ratio (CMRR): |
> 40
dB |
| Power supply
(for full specifications): |
48 V Phantom power
(± 4 V) |
| Current
consumption: |
3.5 mA |
| Color: |
Matte
black |
| Weight: |
- |
| Microphone
Diameter: |
19 mm (0.75
in) |
| Capsule
diameter: |
19 mm (0.75 in) |
| Output voltage,
RMS: |
2.2V |
| Microphone
Length: |
35 mm (1.38 in) |
| Polarity: |
+V at Pin 2 for
positive sound pressure |
| Connector: |
XLR-3M. Pin 1: shield,
Pin 2: signal + phase, Pin 3: - phase |
|
Relative Humidity (RH): |
Up to
90% |
| Temperature
range: |
-40 °C to 45
°C (-40 °F to 113 °F) |
|
Matching tolerance: |
± 1
dB |
| Phase deviation
for kit: |
<
10° |
|
|
|
|
|
