| DPA d:dicate™ 4011E Cardioid Microphone,
Active Cable |
|
|
|
4011-ER |
|
Omni Microphone, Rear Cable |
 |
|
|
4011-ES |
|
Omni Microphone, Side Cable |
|
|
• Ultra-compact spot or
hanging mic
• Very linear frequency and phase response
• Huge dynamic range
• Low-key appearance
Ideal for unobtrusive spot miking, such as hanging or table use,
the 4011E is an ultra-compact cardioid microphone from the modular
DPA d:dicate Recording Microphones series.
With a length of only 3,5 cm, the low-key appearance of the 4011E
is followed by the SM4000-C suspension mount, which is included in
the package. This allows the 4011E to be hung from the ceiling and
create precise and repeatable positions and angles when spot miking
orchestra sections or ambience atmospheres.
Capable of handling high SPLs without distortion, the 4011E is
perfectly tailored for close-miking applications, minimizing bleed
from other instruments. Therefore chosen for close-miking of
instruments like acoustic guitar, drums or grand piano, the 4011E
with its accessories can be placed for instance in the piano
frame.
At any time and with no tools necessary it is possible to transform
the basic 4011E microphone into a new configuration by combining it
with another DPA microphone capsule or preamp. |
| Directional
pattern: |
Cardioid |
| Principle of
operation: |
Pressure Gradient |
| Cartridge
Type: |
Pre-polarized condenser |
| Frequency
range: |
20 Hz to 20 kHz |
| Frequency range,
± 2 dB: |
40 Hz to 20 kHz |
| Sensitivity,
nominal, ± 2 dB at 1 kHz: |
10 mV/Pa; -40 dB re. 1
V/Pa |
| Equivalent noise
level, A-weighted: |
Typ. 18 dB(A) re. 20 µPa (max. 20
dB(A)) |
| Equivalent noise
level, ITU-R BS.468-4: |
Typ. 25 dB |
| S/N ratio
(A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): |
Typ. 76
dB(A) |
| Total Harmonic
Distortion (THD) at 1 kHz: |
< 1 % up to 139 dB SPL
peak |
| Minimum load
impedance: |
2 kohm |
| Dynamic
range: |
Typ. 121dB |
| Max. SPL, peak
before clipping: |
144dB |
| Output
impedance: |
100 ohm |
| Cable drive
capability: |
100 m (328 ft) |
| Output balance
principle: |
Impedance balancing with Active
Drive |
| Common Mode
Rejection Ratio (CMRR): |
> 40 dB |
| Power supply
(for full specifications): |
48 V Phantom power (± 4
V) |
| Current
consumption: |
3.5 mA |
| Color: |
Matte black |
| Weight: |
109 g (3.8 oz) |
| Microphone
Diameter: |
19 mm (0.75 in) |
| Capsule
diameter: |
19 mm (0.75 in) |
| Output voltage,
RMS: |
2.2V |
| Microphone
Length: |
35 mm (1.38 in) |
| Polarity: |
+V at Pin 2 for positive sound
pressure |
| Connector: |
XLR-3M. Pin 1: shield, Pin 2: signal + phase,
Pin 3: - phase |
|
Relative Humidity (RH): |
Up to 90% |
| Temperature
range: |
-40 °C to 45 °C (-40 °F to 113
°F) |
|
Matching tolerance: |
± 1 dB |
| Phase deviation
for kit: |
< 10° |
|
|
|
|
|
