SOUND DEVICES
 SD-442N Field Production Mixer

| Azden | Sachtler Sound Bags | SHURE | Yamaha |  Sennheiser | Tascam | Sound Devices | Sony ProAudio | Zoom | Contact | Us | Email us |
Home < Main < Field Mixers < Sound Devices 442N

Sound Devices 442N (Nordic)

SD-442N Field Production Mixer    
      
This model has been replaced by SD-552  

The 442 Nordic (442N) Field Production Mixer is virtually identical to the 442, with the exception of its Nordic scale PPM meter instead of the SMPTE-based peak meter on the 442.
 

C931-TA-XL-2

TA3-F to XLR-M 15" Adapter Cable


Product Code:SD442N

Buy Sell sales Sound Devices 422N

Key Features

  • Lundahl transformer-balanced mic or line-level inputs on XLR connectors

  • Transformer-balanced line/tape/mic level output on XLR connectors

  • Continuously adjustable input trim

  • Variable high-pass filter

  • Continuously variable pan control

  • Phantom (48-volt or 15-volt) or "T" microphone powering selected per channel

  • Solo (PFL) channel monitoring in headphones

  • Peak limiters per channel

  • Direct outputs on TA3 locking connectors

  • Transformer-balanced line/tape/mic level output on Hirose connector

  • Balanced line or tape level output on TA3 locking connectors

  • Un-balanced TRS-stereo tape level output on 1/8-inch connector

  • Un-balanced TS-mono mic level output on 1/8-inch connector

  • Sunlight-viewable LED meters with proprietary software-selected ballistics

  • On-board MS stereo matrix, channels 1 and 2

  • Two independent monitor return inputs for monitoring two-camera productions

  • Push pots for setup features keep front panel clutter-free

  • Compact 6061 aluminum chassis

  • Powered by four AA batteries or external 5 - 18 VDC
Specifications
Maximum Gain: 81 dB - mic in to line out
41 dB - mic in to mic out
67 dB - mic in to tape out
101 dB - mic in to headphone out
Frequency Response: 20 Hz - 30 kHz, +0.2, -0.5 dB, -1 dB @ 5 Hz and 50 kHz typical
Equivalent Input Noise: -126 dBu (-128 dBV) maximum. (22 Hz - 22 kHz bandwidth, flat filter, trim control fully up)
Dynamic Range: 115 dB minimum (trim fully down)
THD + Noise: 0.007% typical (1 kHz, +4 dBu at line out), 0.09% max (50 Hz - 20 kHz, +18 dBu at line out, fader fully up)
Output Noise: -100 dBu (-102 dBV) maximum (22 Hz - 22 kHz bandwidth, flat filter, master gain fully up, faders fully down)
High-Pass Filters: sweepable 80 Hz to 240 Hz, 12 dB/oct at 80 Hz, 6 dB/octave at 240 Hz
Temperature: operating: –20°C to 60°C, 0 to 95% relative humidity; (non-condensing), storage: –40°C to 85°C
Powering: internal ±16 V (bi-polar) regulated audio rails, 3.2-8 V range internal batteries, isolated (floating) external DC input jack, 5-18 V
Locking 4-pin Hirose connector, pin-4 = (+), pin-1 = (-)
Metering: 40 segment, sunlight-viewable,
selectable Peak, VU, or Peak (with or without peak hold) + VU ballistics
Weight: 2.0 kg, (4.5 lbs) unpackaged with four alkaline AA batteries
Input Clipping Level: 0 dBu minimum (trim control fully down)
Line Output Clipping Level: (1% THD): 20 dBu minimum
18 dBu minimum w/600 ohm load
Input Type: XLR mic - 2k ohm Z, transformer-balanced, 0 dBu max input
XLR line - 16k ohm Z, transformer-balanced, +40 dBu max input
Output Type: XLR & multi-pin @ line - 85 ohm Z, transformer-balanced, +20 dBu max output
XLR & multi-pin @ mic - 150 ohm Z, transformer-balanced, +6 dBu max output
TA3 line - 1k ohm Z, impedance-balanced, +20 dBu max output
Common Mode Rejection Ratio: 120 dB minimum at 80 Hz, mic input, 100 dB minimum at 10 kHz, mic input
L/R Gain Matching: Mic in to Line Out: ± 0.1 dB
Mic Powering: (each mic selectable):
no power applied, 12 V phantom, 48 V, 12 V T-power
Input Limiters: affects the output of the mic preamps only ('Trim' stage), +18 dBu threshold, 20:1 limiting ratio, 1 mS attack time, 200 mS release time
Output Limiters: threshold selectable from +4 dBu to +20 dBu, 1 dB steps, 20:1 limiting ratio, 1 mS attack time,
200 mS release time
Dimensions: 53 mm x 165 mm x 279 mm (H x W x D), 2.1” x 6.5 x 11"


 

 

Read our blogs