DPA d:dicate� ST4015C Stereo Pair with 4015C Compact Wide Cardioids
|
|
Product Code: ST4015C
 |
� Natural reproduction
� Carefully matched within �1 dB
� Low profile � wide pickup area
� PeliTM Case transportation and protection
Visually discreet, the 4015C Wide Cardioids represent an indispensably
low-profile solution for audio engineers and set designers alike. Tremendously
precise and natural sounding, the compact wide cardioids will excel when used on
choirs, percussion setups, grand pianos, wind instruments, and much more. Also
useful as spot mics for classical recording, the 4015C blends very naturally in
with the main pair.
The DPA ST4015C is a complete DPA 4015C Stereo Pair with two carefully
factory-matched wide cardioid microphones. Even though the standard tolerances
on DPA Reference Standards are extremely low, a stereo match is even closer.
The specially selected DPA 4015C microphones are matched within �1 dB on both
frequency response and sensitivity.
The foam design in the heavy-duty transportation box allows for fast and easy
exchange of microphone/accessory inlays.
Included in this kit
Two carefully matched 4015C wide cardioid microphones, sturdy PeliTM case,
holders, and windscreens. |
|
Directional
characteristics: |
Wide Cardioid |
|
Principle of
operation: |
Pressure gradient |
|
Cartridge type: |
Pre-polarized condenser |
|
Frequency range: |
20 Hz - 20 kHz |
|
Frequency
range,
± 2 dB at 30cm: |
40 Hz - 20 kHz |
|
Sensitivity, nominal+/- 2 dB at 1KHz: |
10 mV/Pa; -40 dB re.
1 V/Pa |
|
Equivalent
noise level A-weighted: |
Typ. 18 dB(A) re. 20
�Pa (max. 20 dB(A)) |
|
Equiv. noise level ITU-R
BS.468-4: |
Typ. 25 dB |
|
S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): |
Typ. 76 dB(A) |
|
Total harmonic distortion
(THD): |
<1% up tp
139 dB SPL peak |
|
Minimum load impedance: |
2 kohm |
|
Dynamic
range: |
Typ. 121 dB |
|
Max. SPL, peak before
clipping: |
152 dB |
|
Output
impedance: |
<200 ohm |
|
Output balance principle: |
Impedance balancing
with Active Drive |
|
Cable drive
capability: |
100 m (328 ft) |
|
Common Mode Rejection Ratio (CMRR): |
> 50 dB |
|
Power
supply: |
48 V Phantom power (� 4 V) |
|
Current consumption: |
2.8 mA |
|
Connector: |
XLR-3M. Pin 1:
shield, Pin 2: signal + phase, Pin 3: - phase |
|
Color: |
Matte black |
|
Weight: |
58 g (2 oz) |
|
Diameter: |
19 mm (0.75 in) |
|
Capsule diameter: |
19 mm (0.75 in) |
|
Length: |
64 mm (2.5 in) |
|
Output voltage, RMS: |
> 4 V |
|
Polarity: |
+V at Pin 2 for
positive sound pressure |
|
Operating temperature
range: |
-40 �C to 45 �C (-40
�F to 113 �F) |
|
Relative Humidity (RH): |
Up to 90 % |
|
Phase deviation for kit: |
< 10� |
|
Matching tolerance: |
� 1 dB |
|
|
|
|
|
