DPA d:dicate� 5015A Surround Kit with 4015 Wide Cardioids
|
|
Product Code:
5015A
|
� Wide pickup area and natural sound
� Five carefully matched microphones
� Ambience pickup with convenient directionality
� PeliTM Case transportation and protection
The DPA 5015A is a complete DPA 4015A surround kit with five carefully
factory-matched wide cardioid microphones. Even though the standard tolerances
on DPA Reference Standards are extremely low, the surround match is even closer.
The specially selected DPA 4015A microphones are matched within �1 dB on both
frequency response and sensitivity from mean of set. The maximum phase response
difference is 5�.
Recording orchestras or other acoustic ensembles sometimes requires a compromise
between blending in the room reverberation and a more precise localization. The
natural response and dynamic range make the DPA 4015As an obvious choice for
Precise tone quality and wide dynamic range make 5015A right for AB, Decca Tree
or surround main arrays like the DPA Wide Cardioid Surround Array.
The foam design in the heavy-duty transportation box allows for fast and easy
exchange of microphone/accessory inlays.
Included in this kit
Five carefully matched, sturdy PeliTM case, holders, and windscreens. |
|
Directional
characteristics: |
Wide cardioid
|
|
Principle of
operation: |
Pressure gradient |
|
Cartridge type: |
Pre-polarized condenser |
|
Frequency range: |
20 Hz - 20 kHz |
|
Frequency
range,
± 2 dB, at 60cm: |
40 Hz - 20 kHz |
|
Sensitivity, nominal+/- 2 dB at 1KHz: |
10 mV/Pa; -40 dB re.
1 V/Pa |
|
Equivalent
noise level A-weighted: |
Typ. 18 dB(A) re. 20
�Pa (max. 20 dB(A)) |
|
Equiv. noise level ITU-R
BS.468-4: |
Typ. 25 dB (correct
with the attenuator in 0 dB or -20 dB setting) |
|
S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): |
Typ. 76 dB(A) |
|
Total harmonic distortion
(THD): |
<1% up tp
139 dB SPL peak |
|
Minimum load impedance: |
2 kohm |
|
Dynamic
range: |
Typ. 121 dB |
|
Max. SPL, peak before
clipping: |
159 dB |
|
Output
impedance: |
<200 ohm |
|
Output balance principle: |
Impedance balancing
with Active Drive |
|
Cable drive
capability: |
100 m (328 ft) |
|
Common Mode Rejection Ratio (CMRR): |
> 60 dB |
|
Power
supply: |
48 V Phantom power (� 4 V) |
|
Current consumption: |
2.8 mA |
|
Connector: |
XLR-3M. Pin 1:
shield, Pin 2: signal + phase, Pin 3: - phase |
|
Color: |
Matte black |
|
Weight: |
158 g (5.6 oz) |
|
Diameter: |
19 mm (0.75 in) |
|
Capsule diameter: |
19 mm (0.75 in) |
|
Length: |
170 mm (6.7 in) |
|
Output voltage, RMS: |
> 5 V |
|
Polarity: |
+V at Pin 2 for
positive sound pressure |
|
Operating temperature
range: |
-40 �C to 45 �C (-40
�F to 113 �F) |
|
Relative Humidity (RH): |
Up to 90 % |
|
Phase deviation for
kit: |
< 10� |
|
Matching tolerance: |
� 1 dB |
|
|
|
|
|
