The SMK-SC4060 Stereo Microphone
Kit is a cost-effective and flexible stereo recording solution
aimed at project studios and for discreet mic setup on stage.
The SMK-SC4060 combines two d:screet™ SC4060s Omnidirectional
Miniature Microphones, Hi-Sens, with a variety of mounting
accessories. These include the BLM6000 Boundary Layer Mount, which
can be used in conjunction with a SC4060 (or any of d:screet™
miniature mics) to place the mic on a reflective boundary such as a
floor, wall, ceiling, piano lid etc, enabling them to capture the
ambient sound of the area. The sound captured from this
“pressure zone” has higher sensitivity, clarity and
intelligibility compared to the sound captured from the "free air"
and serves as a kind of acoustical zoom.
Also included in the kit is among others the DMM0007 soft rubber
holder. This allows all kinds of instruments, from acoustic guitar
through grand piano to drums, to be mounted in the best-sounding
position, using special non-marking adhesive discs
Also available as SMK-SC4061 with a d:screet™ SC4061
Miniature Omnidirectional Microphone, Lo-Sens. |
• 2 x
SC4060 Omnidirectional Mic, Hi-Sens, Black, 3 meter cable, and soft
boost grids
• 2 x BLM6000-B Boundary Layer Mount, Black
• 2 x DAD6001-BC MicroDot to 3-pin XLR (P48) w. Belt Clip
• 1 x DMM0007 Universal Surface Mount, 5 pcs.
• 2 x DMM0011-B Magnet Mount, Black
• 1 x DUA0560 Windscreen, Black, 5 pcs.
• 2 x MHS6005 Microphone Holder for Strings
The SMK-SC4060 kit is still available with the original d:screetTM
4060 Omnidirectional Miniature Microphones without the reinforced
cable relief upon request. |
| Directional
characteristics: |
Omnidirectional |
| Principle of
operation: |
Pressure |
| Cartridge
type: |
Pre-polarized condenser element with vertical
diaphragm |
| Frequency range,
± 2 dB: |
Soft Boost Grid: 20 Hz-20 kHz ±2 dB, 3 dB
soft boost at 8-20 kHz.
High boost grid: 20 Hz – 20 kHz, 10
dB boost at 12 kHz. |
| Sensitivity,
nominal, ±3 dB at 1 kHz: |
20 mV/Pa; -34 dB re. 1 V/Pa |
| Equivalent noise
level A-weighted: |
Typ. 23 dB(A) re. 20 µPa (max. 26
dB(A)) |
| Equiv. noise level
ITU-R BS.468-4: |
Typ. 35 dB (max. 38 dB) |
| S/N ratio, re. 1
kHz at 1 Pa (94 dB SPL): |
Typ. 71 dB(A) |
| Total harmonic
distortion (THD): |
<1% THD up to 123 dB SPL
peak |
| Dynamic
range: |
Typ. 100 dB |
| Max. SPL, peak
before clipping: |
134 dB |
| Output
impedance: |
30-40 Ohm |
| Cable drive
capability: |
Up to 300 m (984 ft) |
| Sensitivity
selection tolerance (at 1 kHz): |
± 1.5 dB |
| Power
supply: |
For wireless systems: Min. 5 V – max. 50 V
through DPA adapter; with DAD6001: 48 V phantom power ±4
V. |
| Weight: |
7.5 g (0.26 oz) incl. cable and MicroDot
connector |
| Connector: |
MicroDot |
| Cable
length: |
3 m (9.4 ft) |
| Microphone
length: |
12.7 mm (0.5 in) |
|
| |
|
|
