SHURE Pro Audio Equipment - Performance Microphone SM81 Instrument Microphone

The Shure SM81 is a high-quality, unidirectional condenser microphone designed for studio recording, broadcasting, and sound reinforcement. Its wide frequency response, low noise characteristics, and low RF susceptibility have made it a standard for applications involving acoustic instruments, especially guitar, piano, and cymbals.

SM81-LC - With windscreen, no cable. Phantom power required.

Features

The SM81 is ruggedly constructed. It operates on phantom power and performs over a wide range of temperatures and humidity conditions. It is furnished with a swivel adapter, attenuator-switch lock, foam windscreen, and case for carrying and storage. Other accessories are available.

0 Hz to 20 kHz frequency response
Flat response curve for accurate reproduction of sound sources
Low noise and high output clipping level
Low distortion over a wide range of load impedances
Cardioid polar pattern, uniform with frequency and symmetric about axis, providing maximum rejection and minimum coloration of off-axis sounds
Low RF susceptibility
Selectable low-frequency response: flat, 6 or 18 dB/octave rolloff
0 dB/10 dB lockable attenuator switch
Phantom powering (DIN 45 596 voltages of 12 to 48 Vdc)
Rugged steel construction for durability
Field-usable over wide range of temperature and humidity conditions

Specifications

Type : Condenser (electret bias)
Polar Pattern : Cardioid (unidirectional) response-uniform with frequency, symmetrical about axis
Output Impedance : Rated at 150 ohms (85 ohms actual)

Recommended minimum load impedance: 800 ohms (May be used with loads as low as 150 ohms with reduced clipping level)
Output Configuration and Connector
Balanced, transformer-coupled output; male XLR connector
Sensitivity (at 1,000 Hz)
Open Circuit Voltage: -45 dBV/Pascal (5.6 mV
(1 Pascal = 94 dB SPL)
Clipping Level (at 1,000 Hz)
800 ohm Load: -4 dBV (0.63 V)
150 ohm Load: -15 dBV (0.18 V)
Total Harmonic Distortion : Less than 0.5% (131 dB SPL at 250 Hz into 800 ohm load)
Maximum SPL (at 1,000 Hz)
800 ohm load: 136 dB (attenuator at 0) 146 dB (attenuator at -10)
150 ohm load: 128 dB (attenuator at 0) 138 dB (attenuator at -10)
Hum Pickup : -3 dB equivalent SPL in a 1 mOe field (60 Hz)
Self-Noise (equivalent sound pressure levels; measured with true rms voltmeter)
16 dB typical, A-weighted
19 dB typical, weighted per DIN 45 405
Signal-to-Noise Ratio
78 dB (IEC 651)* at 94 dB SPL
*S/N ratio is difference between 94 dB SPL and product's equivalent self noise (SPL A-weighted).
Overvoltage and Reverse Polarity Protection
Max. external voltage applied to pins 2 and 3 with respect to pin 1: +52 Vdc
Reverse polarity protection: 200 mA max. (diode-clamped)
Polarity : Positive pressure on diaphragm produces positive voltage on pin 2 relative to pin 3
Cartridge Capacitance : 54 pF
Low Frequency Response Switch Positions : Flat; -6 dB/octave below 100 Hz; -18 dB/octave below 80 Hz
Attenuator Switch Positions (Lockable) : 0 or -10 dB
Power
Supply Voltage: 11 to 52 Vdc, positive, pins 2 and 3
Current Drain: 1.2 mA max.
Environmental Conditions
Temperature:
Storage: -29 degrees to 74 degrees C (-20 degrees to 165 degrees F)
Operating: -6.7 degrees to 49 degrees C (20 degrees to 120 degrees F)
Humidity:
Storage 0 to 95% relative humidity at room temperature (72 degrees to 80 degrees F, 22 degrees to 27 degree C)
Case : Steel construction with vinyl metallic paint finish and stainless steel screens
Dimensions : See User Guide
Weight
Net: 230 grams (8 oz)
Packaged: 740 grams (1 lb 10 oz)

SHURE SM81 Instrument Microphone Performance Microphones

SHURE
SM81 Instrument Microphone Performance Microphones