| General
|
| Power Requirements
|
12 V DC (10.8 V to 13.2 V) |
| Current consumption
|
1.0 A (Connector Input)
0.6 A (PoE+ power supply) |
| Ambient Operating Temperature
|
0 °C to 40 °C (32 °F to 104 °F) |
| Ambient Operating Humidity
|
20% to 90% (no condensation) |
| Storage Temperature
|
-20 °C to 50 °C (-4 °F to 122 °F) |
| Weight
|
Approx. 3.2 kg (7.05 lb) |
| Dimensions (W x H x D) (mm)
|
342 mm x 178 mm x 245 mm(excluding protrusions) |
| Dimensions (W x H x D) (inch)
|
13-15/32 inches x 7 inches x 9-21/32 inches(excluding protrusions) |
| Controller Supported Equipment
|
IP/RS422
AW-UE150W/K, AW-HR140*1, AW-HE130W/K*1, AW-HN130W/K*1, AW-UE70W/K*1, AW-UN70W/K*1, AW-HE40 Series*1, AW-HN40HW/HK*1, AW-HE38HW/HK*1, AW-HN38HW/HK*1 |
| Input/Output Connector
|
- |
| INPUT
|
DC 12 V
IN XLR 4-pin
3G-SDI IN
SMPTE292 / 75 Ω (BNC x 1)
Supported formats:
1080/59.94p*2, 1080/50p*2, 1080/59.94i, 1080/50i, 1080/23.98p, 1080/25p, 1080/23.98PsF, 1080/25PsF |
| OUTPUT
|
ACTIVE THRU OUT
SMPTE292 / 75 Ω (BNC x 1) |
| INPUT/OUTPUT
|
IP CONT:
========
100BASE-TX
----------
PoE+ input
----------
Connection cable: LAN cable, max. 100 m (328 ft)
・When connecting the unit via a switching hub:
Straight cable or a cross cable (category 5 cable), STP (Shielded Twisted Pair) cable recommended
・When connecting the unit directly: Crossover cable (category 5 cable), STP (Shielded Twisted Pair) cable recommended
================
SERIAL CONT (RJ-45):
========
RS-422 (control signals for remote cameras), TALLY OUT
----------
Connecting cable:
Straight cable (category 5e or better shielded cable), max. 1000 m (3280 ft)
----------
TALLY OUT: Open collector output (negative logic)
Maximum voltage resistance DC 24 V, Maximum current 50 mA
================
TALLY/GPIO 1
========
D-sub 25-pin, female, inch thread
----------
TALLY IN : 10 inputs (for receiving photocoupler signals)
----------
GPI : 6 inputs (for receiving photocoupler signals)
GPIO : 5 inputs (for receiving photocoupler signals)
or 5 outputs (open collector outputs, negative logic)
・Input/output switched with menu settings
================
GPIO 2
========
D-sub 25-pin, female, inch thread
----------
GPI : 10 inputs (for receiving photocoupler signals)
GPIO : 10 inputs (for receiving photocoupler signals) or 10 outputs (open collector outputs, negative logic)
・Input/output switched with menu settings
Reserve connectors:
2 connectors (For future expansion feature) |
| LCD Display
|
7-inch Touch Panel GUI Monitor (WVGA (800×480) ) |
| SD Memory Card slot
|
SDHC / SDXC Memory Card Slot x 1 |
| Connection Specifications
|
- |
| No. of Connectable Cameras
|
200 (IP), 5 (RS422) |
| No. of Camera Selection Buttons
|
10 |
| No. of Camera Groups
|
20 (10 units per 1 group) |
| Memory
|
- |
| Preset Memory
|
No. of memory : presets 100 |
| Tracing Memory
|
No. of cameras : Cam1 to Cam10
Recording time, no. of memory settings : Maximum 5 min. total per camera, maximum of 10 settings per camera |
| Other Functions
|
- |
| No. of User Assignable Buttons
|
6 + up to 10 on the LCD menu |
| Pan / Tilt Speed Adjustment
|
7 levels |
| Tally LED display color
|
green / red |
| Note
|
*1: Connection with the AW-RP150GJ is planned for future support. Contact your sales representative for further information on when support will be available for this feature. Use may require a software version update. *2: Level-A support only. |
| PoE+
|
IEEE802.3at standard: DC 42 V to 57 V (Camera Input) |
