| Extron SW2 VGA DA2 AF Two Input, Dual Output VGA and Stereo Audio
Switcher with Front & Rear Panel Inputs |
Product Code: SW2VGADA2AF
 |
The Extron SW2 VGA DA2 A and SW2 VGA DA2 AF are
combination active switchers and distribution amplifiers with stereo audio. Each
switcher provides two inputs and dual buffered video outputs and PC audio
buffering. Both models are ideal for presentation environments requiring a
furniture-mountable switcher with the added convenience of a built-in
distribution amplifier.
The SW2 VGA DA2 A and SW2 VGA DA2 AF provide 300 MHz (-3 dB) RGB video bandwidth
and are compatible with VGA-QXGA and HDTV component video signals. Dual buffered
video outputs allow for simultaneous viewing and recording of the selected input
signal. Active PC audio buffering allows both models to input unbalanced audio
on 3.5 mm stereo mini jacks, and output unbalanced and balanced audio on captive
screw connectors. Balanced audio signals are much less susceptible to hum and
interference over long cable runs.
The SW2 VGA DA2 A offers all input connections on the back panel while the SW2
VGA DA2 AF offers convenient access to I/O connections from the front panel.
Front panel access makes the SW2 VGA DA2 AF an ideal solution for use in podium
applications where one computer-video source is in a fixed location, and the
second source is a laptop. |
� Inputs: Two female 15-pin HD
connectors for computer video; two 3.5 mm stereo mini jacks for audio
� Outputs: Two female 15-pin HD connectors for computer video; captive screw
connector for audio
� 300 MHz (-3 dB) RGB video bandwidth
� Compatible with VGA-QXGA and HDTV component video signals
� Dual buffered video and audio outputs � Allows for simultaneous viewing and
recording of the selected input signal, eliminating the cost of a separate
distribution amplifier.
� ID bits from inputs 1 and 2 are routed to the local monitor output
� Active PC audio buffering � Converts unbalanced PC audio to balanced, line
level signals, eliminating noise over long cable runs.
� Auto-input switching � Automatically switches to the highest-numbered input
with an active video signal.
� Contact closure remote control
� 1", half rack width metal enclosure
� Highly reliable, energy-efficient external universal power supply included,
replacement part #70-775-01 � Provides worldwide power compatibility, with high
demonstrated reliability and low power consumption for reduced operating costs. |
|
Video |
|
Gain |
Unity |
|
Bandwidth |
300 MHz (-3 dB) |
|
Video input and loop through |
|
Number/signal type |
2 VGA-QXGA RGBHV, RGBS, RGsB*, RsGsBs*, HDTV
component video* input
1 VGA-QXGA RGBHV, RGBS, RGsB, RsGsBs, HDTV component video* local
monitor loop-through |
| NOTE |
RGsB, RsGsBs, and HDTV component video inputs and outputs work
in manual mode only. Autoswitching requires TTL level sync on
pin 13 of the 15-pin HD connector. |
|
|
Connectors |
3 female 15-pin HD |
|
Pin connections |
ID bits on pins 4, 11, 12, 15 from inputs 1
and 2: passed to main output
Pin 9 of input 1: floating
Pin 9 of input 2: used for the Show-Me feature |
|
Nominal level |
1.0 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of component video |
|
Minimum/maximum levels |
Analog: 0.4 V to 1.8 Vp-p with no offset |
|
Impedance |
75 ohms |
|
Horizontal frequency |
15 kHz to 145 kHz |
|
Vertical frequency |
30 Hz to 170 Hz |
|
Video output |
|
Number/signal type |
1 VGA-QXGA RGBHV, RGBS, RGsB*, RsGsBs*, HDTV
component video* (follows input type) |
|
Connectors |
1 female 15-pin HD |
|
Nominal level |
1.0 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of component video |
|
Minimum/maximum levels |
0.4 V to 1.8 Vp-p (follows input) |
|
Impedance |
75 ohms |
| NOTE |
ID
bits are passed through from VGA inputs to the VGA output.
|
|
|
Sync |
|
Input type |
RGBHV, RGBS, RGsB*, RsGsBs*, bi-level and
tri-level (HDTV) component video sync |
|
Output type |
RGBHV, RGBS, RGsB*, RsGsBs*, bi-level and
tri-level (HDTV) component video sync (follows input) |
|
Input level |
1.8 V to 5.0 Vp-p |
|
Output level |
TTL: 5.0 V p-p, unterminated |
|
Input impedance |
510 ohms |
|
Output impedance |
50 ohms |
|
Max. input voltage |
5.0 Vp-p |
|
Max. rise/fall time |
40 ns |
|
Polarity |
Positive or negative (follows input) |
|
Audio |
|
Gain |
Unbalanced output: 0 dB |
|
Frequency response |
20 Hz to 20 kHz, �0.05 dB |
|
THD + Noise |
0.002% @ 1 kHz at nominal level (-10 dBV) |
|
S/N |
94 dB at maximum output (unweighted) |
|
Crosstalk |
-50 dB @ 20 kHz, -75 dB @ 1 kHz and below 60
Hz |
|
Stereo channel separation |
96 dB @ 1 kHz |
|
Audio input |
|
Number/signal type |
2 stereo, unbalanced |
|
Connectors |
(2) 3.5 mm mini audio jacks (tip, ring,
sleeve) |
|
Impedance |
22k ohms unbalanced, AC coupled |
|
Nominal level |
-10 dBV (316 mVrms) |
|
Maximum level |
+9 dBV, (unbalanced) at 1% THD+N |
| NOTE |
0
dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
Audio output |
|
Number/signal type |
1 stereo, unbalanced |
|
Connectors |
(1) 3.5 mm mini audio jack (tip, ring,
sleeve) |
|
Impedance |
50 ohms unbalanced |
|
Gain error |
�0.1 dB channel to channel |
|
Maximum level (Hi-Z) |
>+9 dBV, unbalanced at 1% THD+N |
|
Maximum level (600 ohm) |
>+7 dBV, unbalanced at 1% THD+N |
|
333Control/remote � switcher |
|
Contact closure |
(1) 3.5 mm captive screw connector, 3 pole
for momentary contact |
|
Contact closure pin
configurations |
1 = input 1 select, 2 = input 2 select, 3 =
GND
Shorting all three pins together enables autoswitch mode. |
|
Loop signal |
Momentary low, 250 �s |
|
General |
|
External power supply |
100 VAC to 240 VAC, 50-60 Hz, external; to
12 VDC, 1 A (max.), regulated |
|
Power input requirements |
12 VDC, 0.1 A |
|
Temperature/humidity |
Storage: -40 to +158 �F (-40 to +70 �C) /
10% to 90%, noncondensing
Operating: +32 to +122 �F (0 to +50 �C) / 10% to 90%, noncondensing |
|
Cooling |
Convection, no vents |
|
Mounting |
|
|
Rack mount |
Yes, with optional 1U rack shelf |
|
Furniture mount |
Yes, with optional under-desk mounting kit
or through-desk mounting kit |
|
Pole mount |
Yes, with optional pole mount kit |
|
Enclosure type |
Metal |
|
Enclosure dimensions |
1.0" H x 4.3" W x 3.0" D (quarter rack wide)
2.5 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.) |
|
Product weight |
0.5 lb (0.3 kg) |
|
Shipping weight |
3 lbs (2 kg) |
|
Vibration |
ISTA 1A in carton (International Safe
Transit Association) |
|
Regulatory compliance |
|
|
Listings |
CE, c-UL, UL |
|
Compliances |
CE, C-tick, FCC Class A, ICES, VCCI |
|
Warranty |
3 years parts and labor |
|
| |
|
|
| |
|
|
