DPA d:dicate� 5006-11A Surround Kit with 4006A omnis and 4011A
cardioids
|
|
Product Code:
5006-11A
 |
� Three + two carefully matched
microphones
� Decca Tree front + cardioids rear
� Specially useful as orchestral main pair
� PeliTM Case transportation and protection
The DPA 5006-11A is a complete surround kit combining three DPA 4006A and two
4011A, carefully factory-matched to achieve full precision. Even though the
standard tolerances on DPA Reference Standard Mics are extremely low, the
surround match is even closer.
The specially selected DPA 4006A microphones are matched within �0.5 dB on both
frequency response and sensitivity. The maximum phase response difference is 5�.
The 4011A�s are matched within �1 dB.
The natural sound, high sensitivity, low noise-floor and extremely linear
frequency response from 10 Hz to 20 kHz (�2 dB) of the microphones make the
4006As the perfect choice for all AB Stereo, Decca Tree or surround main array
recordings. The precise reproduction, total transparency and natural-sounding
clarity of a DPA 4006A microphone will provide you with a lifetime of satisfying
listening.
The foam design in the heavy-duty transportation box allows for fast and easy
exchange of microphone/accessory inlays.
Included in this kit
Carefully matched microphones, sturdy PeliTM case, holders, grids, and
windscreens. |
|
Directional
characteristics: |
4006A:
omnidirectional. 4011A: cardioid. |
|
Principle of
operation: |
4006A: pressure. 4011A pressure gradient. |
|
Cartridge type: |
Pre-polarized condenser |
|
Frequency
range,
± 2 dB: |
4006A: 10 Hz to 20
kHz. 4011A: 40 Hz to 20 kHz. |
|
Sensitivity, nominal+/- 2 dB
at 250 Hz: |
4006A: 40 mV/Pa; -28
dB re. 1 V/Pa |
|
Sensitivity, nominal �2 dB at 1 kHz: |
4011A: 10 mV/Pa; -40
dB re. 1 V/Pa |
|
Equivalent
noise level A-weighted: |
4006A: Typ. 15 dB(A)
re. 20 �Pa (max. 17 dB(A)). 4011A: Typ. 18 dB(A) re. 20 �Pa (max. 20 dB). |
|
Equiv. noise level ITU-R
BS.468-4: |
4006A: Typ. 27 dB
(max. 29 dB). 4011A: Typ. 25 dB (correct with the attenuator in 0 dB or -20 dB
setting). |
|
S/N ratio,
re. 1 kHz at 1 Pa (94 dB SPL): |
4006A: Typ. 79 dB(A).
4011A: Typ. 76 dB(A). |
|
Total harmonic distortion
(THD): |
<1% up tp
139 dB SPL peak |
|
Minimum load impedance: |
2 kohm |
|
Dynamic
range: |
4006A: Typ. 124 dB. 4011A: Typ. 121 dB. |
|
Max. SPL, peak before
clipping: |
4006A: 147 dB. 4011A:
159 dB. |
|
Output
impedance: |
<200 ohm |
|
Output balance principle: |
Impedance balancing
with Active Drive |
|
Cable drive
capability: |
100 m (328 ft) |
|
Common Mode Rejection Ratio (CMRR): |
> 60 dB |
|
Power
supply: |
48 V Phantom power (� 4 V) |
|
Current consumption: |
2.8 mA |
|
Connector: |
XLR-3M. Pin 1:
shield, Pin 2: signal + phase, Pin 3: - phase |
|
Color: |
Matte black |
|
Weight: |
4006A: 163 g (5.7 oz). 4011A: 158 g (5.6 oz). |
|
Diameter: |
4006A: 16 to 19 mm
(0.63 to 0.75 in). 4011A: 19 mm (0.75 in). |
|
Capsule diameter: |
4006A: 16 mm (0.63
in). 4011A: 19 mm (0.75 in). |
|
Length: |
170 mm (6.7 in) |
|
Output voltage, RMS: |
> 5 V |
|
Polarity: |
+V at Pin 2 for
positive sound pressure |
|
Operating temperature
range: |
-40 �C to 50 �C (-40
�F to 122 �F) |
|
Relative Humidity (RH): |
Up to 90 % |
|
Phase deviation for
kit: |
< 10° |
|
Matching tolerance: |
4006A: � 0.5 dB. 4011A: � 1 dB. |
|
|
|
|
|
