AZDEN Pro Audio Wireless
Powered Speaker

Home   Audio Tech   Sennheiser Tascam Shure Sound Devices Canon Sony ProAudio Sony Panasonic JVC E-Shop Contact us Visit Singapore Store
> Home > AZDEN > AC and Battery Speakers > APS 25-RH2
APS 25
APS 25-RH1
APS 25-RH2
APS 25-RL1
APS 25-RL2
APS 25-RS1
APS 25-RS2
APS 25-UH1
APS 25-UH2
APS 25-UL1
APS 25-UL2
APS 25-US1
APS 25-US2
APS 25-VH1
APS 25-VH2
APS 25-VL1
APS 25-VL2
APS 25-VS1
APS 25-VS2


 AZDEN APS 25-RH2 Powered Speaker System


The APS 25-RH2 powered speaker system is a fully self-contained wireless sound reinforcement system with two infrared wireless handheld microphone/transmitters.
Incorporating a 20 watt amplifier, the APS 25 is a rugged, 2-way speaker with a 5.25" shielded woofer and a 1" wide-dispersion tweeter that produces clear detailed sound for all corporate, educational and commercial applications.

The APS 25 includes a Master Volume control and Tone control to reduce feedback. Individual level controls for each of the four inputs- two wireless, one wired mic level, and one line level-giving you more ways to configure your system. The speaker's variable line level output lets you daisy chain multiple speakers. The high gain mic input shorts automatically to reduce noise when no mic is plugged in. Included with the APS 25 is the Auto On-Off circuitry triggered by any audio input signal for hands-off system startup; a high impact case for reliability, and dual-voltage(110/220V) switching to facilitate installation and use. The speaker can be used free standing, stand-mounted (5/8x27 threaded holes on the bottom and side) or wall-mounted with the supplied U-mount bracket.

The APS 25-RH2 includes two APS-IRII infrared receiver modules, two IRH-15c microphones and an IRD-30 external sensor with a special sensor interconnect cable.

For pass-around, use the 2-channel IRH-15c infrared handheld uni-directional mic/transmitter. Multiple emitters around the base and near the mic element flood the room. An anti-roll ring around the mic head keeps the IRH-15c from rolling off a sloping lectern or school desk.

Speaker Technical Specs:
Rated Power: 20 Watts continuous
Frequency Response: 65Hz – 18kHz
Max SPL @ Rated Output: 101db @ 1 meter
Woofer: 5.25" (133.35mm) high efficiency - magnetically shielded
Tweeter: 1" (25mm) dome
Crossover: 1st order passive @ 8kHz
Tone Control: -6dB/octave sliding low pass (3kHz to 8kHz)

Wireless Inputs: 2 user-installable receivers
VHF (169-213 MHz) – 30 fixed frequencies
UHF (566.25-589.75 MHz) – 92 user-selectable frequencies
Infrared – 2 fixed frequencies

Wired Inputs/Output:
Mic: -81dBv (0.089mVRMS) for 1 watt, 100K balanced, ¼" phone jack, variable
Line: -40dBv (10mVRMS) for 1 watt, 10K unbalanced, RCA jack, variable
Line-Out: +15dBv max - RCA jack

Weight: 8.5lb (3.85kg) approx. w/out receivers
Dimensions: 12.4"H X 7.09"W X 5.6"D (315 X 180 X 142mm)
Compliance: UL, C-UL, and FCC approved
AC Power Requirements: User switchable, 110-125 / 210-240VAC - 50Hz/60Hz

Included w/speaker: Removable wall-mount bracket with 2 screws, rubber anti-rotate pads, removable right-angle, AC cord, 4 self-adhesive anti-skid pads, 4 module screws, 1 or 2 noise-canceling circuit boards (depending on how many modules are installed

Receiver Technical Specs:
Sub-carrier frequencies: 2.06MHz or 2.56MHz
Type: super heterodyne - crystal controlled
Modulation: FM
Signal-to -Noise: >90dB
Image rejection: >40dB
Reception sensitivity: >25dBµV
Reception selectivity: ± 40kHz
Audio output adjustment: +4dB max
Audio output impedance: <1k ohms

Transmitter Technical Specs:

Sub-carrier frequencies: 2.06MHz & 2.56MHz switchable
Modulation: FM
Microphone element type: Uni-directional dynamic
Frequency Response: 50-8kHz ±3dB
Battery type: 2-“AA” alkaline( 1.5V x 2 ) or
2-“AA” rechargeable Ni-MH (1.2V x 2 )
Battery life: > 6 hours w/alkaline batteries
Size: 9.65" x approx.1.375" (245 x approx. 35mm)
Weight: 9.1oz (258g) w/alkaline batteries)


Read our blogs