|
|
|
|
|
| |
|
AZDEN APS
25-RL2 Powered Speaker System (Discontinued)
|
|
|
The APS 25-RL2 powered
speaker system is a fully self-contained wireless sound
reinforcement system with two infrared wireless chest-worn
transmitters.
Incorporating a 20 watt amplifier, the APS 25 is a rugged, 2-way
speaker with a 5.25" shielded woofer and a 1" wide-dispersion
tweeter that produces clear detailed sound for all corporate,
educational and commercial applications.
The APS 25 includes a Master Volume control and Tone control to
reduce feedback. Individual level controls for each of the four
inputs- two wireless, one wired mic level, and one line
level-giving you more ways to configure your system. The speaker's
variable line level output lets you daisy chain multiple speakers.
The high gain mic input shorts automatically to reduce noise when
no mic is plugged in. Included with the APS 25 is the Auto On-Off
circuitry triggered by any audio input signal for hands-off system
startup; a high impact case for reliability, and
dual-voltage(110/220V) switching to facilitate installation and
use. The speaker can be used free standing, stand-mounted (5/8x27
threaded holes on the bottom and side) or wall-mounted with the
supplied U-mount bracket.
The APS 25-RL12 includes two APS-IRII infrared receiver modules,
two IRN-10 chest-worn transmitter with emitter/mics and an IRD-30
external sensor. An included external emitter interconnect cable
allows a single sensor to operate both receivers
Speaker Technical
Specs:
Rated Power: 20 Watts continuous
Frequency Response: 65Hz – 18kHz
Max SPL @ Rated Output: 101db @ 1 meter
Woofer: 5.25" (133.35mm) high efficiency - magnetically
shielded
Tweeter: 1" (25mm) dome
Crossover: 1st order passive @ 8kHz
Tone Control: -6dB/octave sliding low pass (3kHz to 8kHz)
Wireless Inputs: 2 user-installable receivers
VHF (169-213 MHz) – 30 fixed frequencies
UHF (5666.25-589.75 MHz) – 92 user-selectable frequencies
Infrared – 2 fixed frequencies
Wired Inputs/Output:
Mic: -81dBv (0.089mVRMS) for 1 watt, 100K balanced, ¼" phone
jack, variable
Line: -40dBv (10mVRMS) for 1 watt, 10K unbalanced, RCA jack,
variable
Line-Out: +15dBv max - RCA jack
Weight: 8.5lb (3.85kg) approx. w/out receivers
Dimensions: 12.4"H X 7.09"W X 5.6"D (315 X 180 X 142mm)
Compliance: UL, C-UL, and FCC approved
AC Power Requirements: User switchable, 110-125 / 210-240VAC -
50Hz/60Hz
Included w/speaker: Removable wall-mount bracket with 2 screws,
rubber anti-rotate pads, removable right-angle, AC cord, 4
self-adhesive anti-skid pads, 4 module screws, 1 or 2
noise-canceling circuit boards (depending on how many modules are
installed
Receiver Technical
Specs:
Sub-carrier frequencies: 2.06MHz or 2.56MHz
Type: super heterodyne - crystal controlled
Modulation: FM
Signal-to -Noise: >90dB
Image rejection: >40dB
Reception sensitivity: >25dBµV
Reception selectivity: ± 40kHz
Audio output adjustment: +4dB max
Audio output impedance: <1k ohms
Transmitter Technical
Specs:
Sub-carrier frequencies: 2.06MHz & 2.56MHz switchable
Modulation: FM
Microphone element type: Uni-directional electret x 2
Frequency response: 50-9kHz ±3dB
Ext Mic input impedance: 2.2k ohms Ext Mic input jack: 3.5mm
Ext. Mic Voltage/Current: 3.5VDC @ 1mA (to power electret mic
element)
Mic gain adjustment: +6dB to approx. –10dB
Battery type: 2-"AA" Alkaline (1.5V x 2) or
2-"AA" rechargeable Ni-MH (1.2V x 2)
Battery life: > 8hours w/alkaline batteries
Size: 3.15" H x 2.75" W x 1.06" D (80 x 70 x 27mm)
Weight: 4.3oz (120g) -w/alkaline batteries |
 |
|
| |
|
> AZDEN > AC and Battery Speakers > APS
25-RL2
