Tempest TMP-RT09 900MHz Remote Transceiver

tempest TMP-RT09 Transceiver with Omni Antenna
TMP-RT09 Remote Transceiver TMP-RT09 Remote Transceiver  

Tempest900 900MHz Remote Transceiver with Omni Antenna

Product Code: TMP-RT09

Tempest900 900MHz Remote Transceiver


Features

  • For use with the Tempest900 BaseStation
  • Allows remote location of antenna from the base with no RF signal loss
  • Cable runs of up to 1500 ft. (450 m)
  • Operates on standard CAT 5/6 cable
  • Power is provided over the cable from BaseStation
  • Durable aluminum alloy enclosure
  • Weather-resistant for outdoor use,Rx, Tx, Sync, Config, and Power LED indicators
  • mRP-TNC antenna connectors
  • Includes One omni-directional 2 dBi antenna
  • Can remote antenna from the Transceiver with low loss coaxial cable
  • Only available in US and Canada

The Tempest900 Remote Transceiver allows the Tempest900 BaseStation antenna to be located up to 1500 ft (450m) from the BaseStation without any loss of RF signal. The RT is connected to the BaseStation via a standard CAT-5/6 cable using RJ-45 connectors. Power is provided over the CAT-5/6 cable so that no local power is required for the Remote Transceiver to operate normally. The RT is constructed of aluminum alloy. It comes with a universal mounting plate that can be used to mount the transceiver to poles, walls or other desired areas.

OPERATION
One Remote Transceiver can be connected to a single Tempest BaseStation (2- or 4-channel). A direct connection is required. (The transceiver will not operate properly if connected to a Local Area Network (LAN) or routed through a network device such as a router or switch.) The transceiver has two RP-TNC antenna connectors on top of the enclosure that can attach the standard 2dBi omni-directional antennas, or employ optional directional antenna via low loss coaxial cable.

LED INDICATORS
The Remote Transceiver is equipped with five LED indicators so that the user can ensure proper operation of the transceiver.

-Power LED illuminates whenever the BaseStation is providing adequate power to the transceiver over the CAT-5/6 cable.
-Sync and Config LEDs indicate that the transceiver has been properly connected.
-Receive (Rx) and Transmit (Tx) LEDs indicate proper data transfer to and from the BaseStation and wireless BeltStation.

DURABILITY
The Remote Transceiver is weather resistant and is intended for use outdoors. It is recommended, however, that in extreme weather conditions appropriate measure are taken to ensure that no water enters into the enclosure.

System Specifiations
RF Frequency     902 to 928 MHz
RF Scheme FHSS with TDMA
Effective Radiated Power 250mW using 2dBi antenna
Receiver Sensitivity -100 dBm for 10-5 BER
Radio Certification FCC Part 15, Canadian RSS-210, license free
Transmission Range 1,000 ft. (304.8 m) under ideal conditions. 500 ft. to 900 ft. (152.4 m to 274.3 m) typical
Audio Dynamic Range >94 dB
Audio Frequency Response 300Hz–3.8KHz with proprietary audio voice shaping
System Latency Less than 60 ms direct
Transceiver Specifications
Maximum Cable Length, Base to Transceiver  1,500 ft. (457.2 m), powered from the BaseStation 
Connection to BaseStation   CAT-5 standard wiring 
BaseStations Supported per Transceiver 
Number of Antenna Ports per Transceiver  
Antenna Connector Type  RP-TNC  
Supplied Antenna   Whip antenna 
Dimensions with Antennas (inches) H 12 in. × W 3.7 in. × D 1.7 in. (304.8 mm × 94 mm × 43.2 mm)
Weight 11 oz (312 g)
Operating Environment -20° to 50° C (-4° to 122° F); 10% to 90% Humidity
  • Antenna (X1)
  • Universal Mounting Plate with Screws (X2)
  • 15ft. (4.57 m) CAT-5e Etheernet Cable